Jump to content
SAU Community

Formula One 2012

N1GTR

By N1GTR,
in Motorsport Discussion & Builds

 Share

Recommended Posts

  • Replies 5.5k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

Doobs Proficient

Doobs

Posted
Posted

did anyone else hear what sounded like Hamilton's car very briefly touching the rev limiter before braking into the final turn?

they've obviously been geared to not have to overtake people under DRS. no wheelspin off the start tomorrow son...

I noticed Webber was maxed out at the final turn as well.

MattR Veteran

MattR

Posted
Posted

damm you rosberg, i had high hopes for him in quali, cant handle the pace. he needs to take a page out of his old mans book and have a smoke before he gets in the car. vetool almost looked like he was going to cry, how many races can he go without a pole?

Tangles Grand Master

Tangles

Posted
Posted

Vetool smokes plenty of pole prior to each race....

Button to win, and most likely the championship.

Webber to outrace the 'Tool and place well, once he makes up the positions he loses off the line

Masa to tangle tyres and punt himself out of the race

The old boy Shumi looks like he'll have a good season. McLaren and Mercedes look like they've benefited the most from the blown diffusers being changed. Can RBR find some pace?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTST Steering Rack (49001-19U05) Rebuild?

      By GTSBoy · Posted

      I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • WMDC35
      Wheel Sizes & Offsets For Skylines

      By WMDC35 · Posted

      A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Duncan
      RB20DE NEO smallbox clutch.

      By Duncan · Posted

      Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • GTSBoy
      RB20DE NEO smallbox clutch.

      By GTSBoy · Posted

      Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Kapr
      RB20DE NEO smallbox clutch.

      By Kapr · Posted

      Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
×
×
  • Create New...