Jump to content
SAU Community

Recommended Posts

he was only off the track because Hamilton forced him off...

if you squeeze someone that hard, you have to realise it comes with a risk of collision.

The whole situation was caused by Hamilton, who had no chance of hanging on to that position anyway.

Exactly.

Hamo's arrogance kicked in as usual - and Pasta did what he does best.

Hamo was going to be overtaken anyway, he knew this - so just give up, take the loss of position and don't miss out on any points.

His post-race kinda summed that up the way he avoided the question "i dont remember". cops arse he didn't. He remembered exactly and new he had a part to play regardless of who was "as fault" as determined by the stewards

  • Replies 5.5k
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

he was only off the track because Hamilton forced him off...

unh4i.jpg

if you squeeze someone that hard, you have to realise it comes with a risk of collision.

The whole situation was caused by Hamilton, who had no chance of hanging on to that position anyway.

No way.

Hamilton was brilliant there (I hate hammy). Shoved him off the track leaving zero room. You either yield and slot back in to overtake elsewhere or crash. Most drivers have the common sense not to crash... He only had 1.5ish laps to go? Sorry but if I was in Hamilton's shoes I would've done the same and defended like crazy.

don't the 2012 regs read that you must leave a car width available? Hamilton drove Maldenardo off the track, and Maldenardo hit him. IMO they both should get a penalty

I think the rule is along the lines of they are only allowed to move once to cover an attack, they cannot repeatadly attempt or something.

It was raised in i think Shanghai or KL

he can run him out of room on the exit, under braking is where the new rules stop people like schumacher chopping you off the track

Hamo did the right thing and pushed Pastor wide as he had the racing line, Pastor refused to accept the failed attempt and brain faded for a fourth time now, taking out Hamo and himself by hitting him in the rear of the coke bottle

What hamo was doing by keeping him behind is what called racing, what pastor did is called gp2

Pastor kept his foot in it, while off track, and had nowhere to rejoin BUT into the side of his opponents car. Total and utter balls up. Yet again

Is he far enough up the side for Hamo to leave him a car width? It kinda looks like he was.

If Maldonado didn't back out at the apex of the first turn then it was always going to end in tears when Hamo turned into the apex of the next corner.

the rules actually say "deliberate crowding of a car beyond the edge of the track is not permitted"

very harsh to penalise Maldonardo IMO. Penalise both or neither.

Edited by hrd-hr30

what was truly appalling was how Senna was penalised for the contact with KK

Agreed, was quite surprised to see him get a drive through for being driven into.

the rules actually say "deliberate crowding of a car beyond the edge of the track is not permitted"

very harsh to penalise Maldonardo IMO. Penalise both or neither.

How did you feel about the defending that Rosberg did a few races ago (can't remember which track :blush: ) on the straight?

Hamilton had the racing line...Maldonado was never going to make that pass around the outside into that corner, so he should have yielded and set himself up for the next few corners.

He would've passed him no worries, but he got impatient and drove straight into him instead.

As Ivan stated, it's called racing. If there was 10 laps to go Hamilton would've more than likely let him passed without a fight as he would've lost time defending a position he was never going to keep, but with a lap and a half to go, any race worth their salary is going to defend hard.

Hamilton had the racing line...Maldonado was never going to make that pass around the outside into that corner, so he should have yielded and set himself up for the next few corners.

He would've passed him no worries, but he got impatient and drove straight into him instead.

As Ivan stated, it's called racing. If there was 10 laps to go Hamilton would've more than likely let him passed without a fight as he would've lost time defending a position he was never going to keep, but with a lap and a half to go, any race worth their salary is going to defend hard.

/thread

i think this was covered slightly a bit back, but didnt anyone else notice the way that webber in his pre-race interview felt like he was swaying towards fezza team.

if he went number 2 there i beleive he would be taking a step backwards. number 1 driver or bust........

i think this was covered slightly a bit back, but didnt anyone else notice the way that webber in his pre-race interview felt like he was swaying towards fezza team.

if he went number 2 there i beleive he would be taking a step backwards. number 1 driver or bust........

Better find himself 3 WDC titles...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
    • Just one thing; tapping tapered threads is tricky. Taps are always tapered and you would generally run it as far as you can, but with a tapered thread you have to stop much sooner otherwise the wide part of the taper will run in too far and you will have to thread the sensor in too far too as well (possible that it will never make a good seal) BTW nice wide wheels, I guess the top one is for the back!
    • Welp, good to know. Will have to wait awhile until steady hands with drills and taps are available. In other news, these just arrived! I will weigh them for posterity. Edit: 11kg each (or 10.9/11.1 depending on what my scale decides over multiple tests, the 18x11 don't seem to weigh noticeably any more than 10.5)  
×
×
  • Create New...