Jump to content
SAU Community

Recommended Posts

Hi all,

Yesterday I installed an Apexi Power Intake into my R33 GTR. They replaced the dodgy wire mesh type fake alloy pods that were in it when I bought it.

I have noticed though that now the responsiveness has been diminished somewhat. I am assuming that this is because the airflow is more restricted with the Apexi (proper) pod filters rather than just wire mesh.

My car was slightly tuned when we lived in Perth, basically adjusted the timing slightly and removed the boost restrictor.

I am thinking I need to have it stuck on a dyno and the timing re-adjusted to suit the new intake system.

Can anyone give me an idea of the cost in Canberra to have someone do this? And any suggestions on where to take it would be appreciated. I am aware of Ultimate Tunes, which is 10 minutes up the road from me.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/384833-dyno-time-cost-in-act/
Share on other sites

Just jump on the phone and call around.

Everyone will pretty much be willing to beat the other person.

Just get as many quotes as you can

Then go to one of the guys like listed ESP or Trojan and tell them what you were quoted.

See if they can beat that

Little off topic but I did this with my windscreen and saved myself $150 + got a new seal

Thats still true. How hard can it be to set up a dyno?

I've never asked them but given the size of their workshop maybe it's got to do with the lack of room? Although that then makes you wonder why they have it in the first place.

I've never asked them but given the size of their workshop maybe it's got to do with the lack of room? Although that then makes you wonder why they have it in the first place.

they just need to park a few more skylines outside to make room lol

I'll wanna dyno tune my can when put in the electronic boost control to get the settings just right too.... Need to call round and see what i can get for that....

Any one seen and good threads with advise for setting one up? Or any one have much experience at it?? Had no luck searching so far.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...