Jump to content
SAU Community

Recommended Posts

recently finished my build and went in for a tune. asked the mechanic to boost it to 17 psi as Ive been told by mates in the know" she be right"

old mate mechanic only tuned it up to 14psi not recommending going any higher unless i really want to lol

ok ive done:

PWR FMIC

Sard 555cc injectors

Nismo fuel pump

Apexi PFC

Z32 AFM

Spit Fire Coils

Tomei Pon cams

Custom Hiflow turbo (zorst side larger)

Blitz EBC

Ive got stock internals stock head gasket and i ran 235rwkw as 14psi. can i run 17psi with what i got?

Thanks David

Link to comment
https://www.sau.com.au/forums/topic/385018-boosting-a-r33-with-stock-internals/
Share on other sites

Depends what this "custom high flow" turbo is?

eBay specia?

haha not a ebay special. a mate of a mate worked for garret and done up 10 with dump pipe as a side project. ball bearing rated to 500hp

i got the last one and all feedback has been positive.

Just be careful. Fitting a 500hp cartridge to bored out stock housings never ends as well as expected.

Tune to to about 18psi but only within detonation and inlet air temp limits.

It's hard to say where the efficiency is in an unknown bastardized turbo.

There isn't really a set number, its more like how high does your tuner want to go with it. A mates R33 was on 1.5Bar for a good 4 years without a problem, only blew when he turned it up to 2bar without retuning it or anything lol.

Mines tuned for 17psi. Has been like that for a few months now, and had a good beating at the track where it was getting up to 1.4bar briefly too.

Lithiums R33 was tuned for 17-18psi for over 100,000km, and not many of them were nana km either.

Its all in the tune :) Rather than go be a KW queen, settle for a lower number with safer ignition if you cant afford/dont want to rebuild/replace.

I gave mine 1.45bar in winter and 1.3bar in summer all year round no dramas, didn't see anything go pop.. A/Fs were 12 and dipping to 11.5 at MBT and back up to 12 towards redline. A few people have seen how I drive my car too, driven like Nissan intended it to be driven.

  • Like 1

As stated the boost level isnt your limiting factor, its where your turbo runs out of puff (so to speak).

There will come a point where the turbo is simply pumping hot air and it will mean a bad tune ETC. With the right turbo theres nothing to stop you putting over 20psi into the stock motor, even that is nothing special.

this is a very valid topic and i think there are a lot of myths out there

and a lot of people get caught up on i want xxx rwkw and i have to run xyz psi

there is no magic limit or safe level for an engine for boost

why? because boost is simply the amount of resistance, nothing more

the less boost you can run the better

the more boost you run, the more stress and less efficient it becomes

the old hat method is keep winding in boost until you peak torque, airtemp doesnt ramp and you continue gaining power

ie why run 22psi when you stop making power/torque with anything past 16psi?

the point is

your tuner should dictate this type of value and tune as best he or she can within the turbochargers limits

exhaust back pressure is also a big concern so why run more boost if its of no gain

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • There are several aftermarket options available, from not-too-painful moneyhttps://justjap.com/collections/driveshafts-bearings/products/d-max-reinforced-replacement-rear-driveshaft-set-fits-nissan-s13-s14-s15-r32-r33-r34-c35 and  https://justjap.com/products/crank-motorsport-billet-rear-axles-fits-nissan-skyline-r33-gts-t-r34-gt-t?srsltid=AfmBOorQk4xkGUa98kO7v2ePLUiNt-HRrM2AwWNw9mbSIVE1ujBVwY__, all the way up to The Driveshaft Shop https://driveshaftshop.com/skyline-cv-axles/
    • Yeah based on old XRC5964S specs, it looks to be roughly GTX3576R sized? But this 5964S compressor will flow 90lb airflow somewhat similar to the compressors in both the GTX3584RS or G35-1050.. I fully expected the 0.64 rear A/R to choke up top - seems way too small from typical convention - but these are seemingly beneficial over the prior 0.82 results.. Be interesting to see if he comments on the EFR question in that thread - he mentioned in a prior video that BW EFR's were the "cats pajamas 10 years ago", but by the sounds of things all his kits have been using Xona for quite a while now.
    • Yeah it’s still got the oem manual gearbox and clutch, only kinda mods are a blow off valve, coil overs, and a aftermarket intercooler. Also had it for about 2 months now with a lovely midnight purple paint on it.
    • Yeeeppp, been following a lot of the testing on the latest Xona stuff and there are some mental results.  He also went over 1000hp @ 4 hubs on his Mainline with a XRE6364S (63mm) which was also well into the 20psi range before 4000rpm on a 2.5. Crazy stuff. Fwiw the XRE5964S is basically the modern equivalent of their old HTA3582 - would drive nicely enough on an RB25 or 26, but proven capable of a huge amount of power if you want to spicy with rpm tho even at sane boost levels will make stout numbers 
    • The axels in my R33 seem tired, and have a bit of play in them. I cannot find any new of course, not interested in buying used, but I am looking to see if anyone can identify some cross compatible axles. In the states I have seen suggested for S chassis the J30 axles, however for the skyline (as best I can tell) the lengths are about an inch off (2.5cm) on both sides. R33 my measure L 22" R 24.5" GPT L 22.5" 24.25" J30 L 23.5" 25.5"  so shaft length is probably an inch wider. Not sure if someone has another still remanufactured option besides the J30. I figured worst case I can buy a pair tear them down and swap the center shaft. My other option was reaching out to GSP to see if they cannot piece together a set, since the axle stubs are still manufactured, I wouldn't think it be that hard to find a shaft or make a shaft work. 
×
×
  • Create New...