Jump to content
SAU Community

Setting Up My Christmas Greddy Profec

Manuel Kasko

By Manuel Kasko,
in Engines & Forced Induction

 Share

Recommended Posts

Manuel Kasko Grand Master

Manuel Kasko

Posted
Posted

Hey guys

So I got a Greddy Profec 2 for Christmas off the partner and its proving to be a pain to setup.

I ended up tapping into the vac line that the stock gauge uses (dont know if this is an issue)

Right now it seems to not want to go over 6psi

If anyone knows anything about these then let me know.

Settings I currently have it set to.

SET: 35%

GAIN: 5%

SET GAIN (start boost): 7psi

WARNING: 11psi

LIMITER: 5%

I think there might be a vac leak because when I pull the line off the nipple on the intercooling piping that goes to the solinode and the VAC on my gauge does not change a bit.

On idle sites around probably 20 or so

This makes me think there is already a big enough vac leak that by me doing this does not cause any issues

Here is a picture of what my VAC looks like when coming off throttle. (very bad)

1zf0xfb.jpg

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

Scrarching my head - so u connected it to the boost gauge sensor? Or the stock boost solenoid near the turbo?

U need to run it from the cooler pipe to the NEW boost controller solenoid then to the wastegate.

Then T into a vacuum/boost source such as the stock boost gauge sensor on firewall and run that one into the cabin into the boost controller

Manuel Kasko Grand Master

Manuel Kasko

Posted
  • Author
Posted

Haha nah sorry

The controller is hooked up to the actuator and the nipple on the cooler piping. All correct.

But my gauge sits at around -20 VAC

When I pull the line off the intercooler piping the VAC does not change is that normal? Or should the vac drop because it's got now an exposed nipple on the intercooler piping?

It also sounds like a sewing machine on boost which leads me to believe its defiantly got a leak somewhere.

But one question as well is for the boost gauge part of the profec I pulled the hose off from the stock vacuume line where it enters the air intake and ran a hose straight to my profec. Is that okay to do?

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

Can u post up a pic of the vacuum line ur talking about?

The cooler pipe line is before the throttle body so it wint really affect ur gauge reading after the throttle body. If that makes sense?

What do u mean by a sewing machine?

Try upping the gain to 15, set the boost warning to 15psi.

Watch the boost gauge and see if it holds flat or if it oscillates up and down

Manuel Kasko Grand Master

Manuel Kasko

Posted
  • Author
Posted

I will take a pic tomorrow of the vac line it comes out of the back of the intake manifold and normally goes to the stock gauge inside the car. Instead I pulled it off and ran my own pipe from it to my gauge in the car

Just has a sewing machine noise hard to describe but as it spools it has a noise like a sewing machine lol

Manuel Kasko Grand Master

Manuel Kasko

Posted
  • Author
Posted

My phone network is down so I cant get pics.

Right now I fiddled with the setup and the T now goes into the fuel regulator VAC line

I put the stock gauge VAC line back onto the back of the intake manifold.

Anyone know of a simple technique to find a VAC leak?

I tried spraying the hoses with "start ya bastered" to see if I could hear a change in revs but I cant find it

When coming off WOT the gauge shows -30 VAC and the Greddy unti shows -99 VAC

Both of which are the lowest numbers they can display

hardsteppa Grand Master

hardsteppa

Posted
Posted
I think there might be a vac leak because when I pull the line off the nipple on the intercooling piping that goes to the solinode and the VAC on my gauge does not change a bit.

. It won't, I believe this part is under mild pressure at idle. Pull a vac line off after the throttle plate and see if the idle changes.
Just has a sewing machine noise hard to describe but as it spools it has a noise like a sewing machine lol
u sure it's not just the boost controller solenoid clicking away, they can be pretty loud.
Manuel Kasko Grand Master

Manuel Kasko

Posted
  • Author
Posted

I pull hoses off and it does not really change so the VAC at -30 is pretty normal?

I think I had it the wrong way around I was thinking your vac went lower when you had a VAC leak.

So if I had a leak I would expect the number to increas to say -20?

the ticking might be the solenoid then I guess because I have never had one I always used the boost T.

GTScotT Grand Master

GTScotT

Posted
Posted

yes its normal to drop lower when you come off WOT, -30 in that case would be fine

you really need to show us how its been hooked up from where to where.

have you tried upping the boost or what? make sure you have the solenoid hooked up right too in terms of in and out

Manuel Kasko Grand Master

Manuel Kasko

Posted
  • Author
Posted

I wish I could get a photo but as I said I am with vodafone so nothing is working haha

The car is running great though.

Boost is tuned for 8psi and 10psi for 2 settings.

It all seems to be running fine now guys

When I get back from the coast I will post up some pictures

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...