Jump to content
SAU Community

Recommended Posts

  • Replies 75
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Thanks mate will do today hopefully.

stock bov goes to the very far left pipe in this pic..

36353845.jpg

That image is a stock R32/R33 GTST intake pipe with all the EGR and BOV return pipes intact.

I assume yours is still there and just blocked off.

Replaced by the looks of things, is the stock setup better or good enough to replace the new pipes? Can I feed it back into their somehow?

aa3f936a.jpg

006ac4d3.jpg

Edited by GH05T

OK, so in that bottom photo, where you can see the blue silicone hose connects onto the turbo inlet pipe (approx 1" hose clamped), that's your crankcase breather connection. The BOV return needs to go onto the same part of the turbo inlet pipe, preferably so that it is aimed towards the turbo rather than aimed towards the AFM. If you don't have another suitable fitting on that intake pipe already, you just need someone to bang a hole in it and weld on a new one, plus run the BOV return.

cheers

Ok, well, I had a productive day today.

Me and some mates were doing the clutch and got some new plugs to see if that was the problem.

Before we did anything we tested the coilpacks and they all seemed to work properly. But when we were f**king about we found one of the vacume lines at the rear of the head to be split

03166fb9.jpg

Very split.

Luckelly we had a blown rb20 their so swapped it out.

Not only did it get rid of the misfire, the starting issue and make everything smooth, when I drove it and hit boost it smashed streight past 1bar.

Dunno what it hit but I have wound the manual boost controller back 2 clicks and it's still above 1 bar.

I can only assume the old owner wound it up to compensate because before it only hit .9 bar as it was. Will be interesting to see how far back I have to wind it to go back to 1bar again.

Turbo seems much happier.

Even the flutter sounds different, mush deeper so it must be making much cleaner boost.

Also in regards to the screamer pipe. Unbolted the bottom clamp when we took the gearbox out when we did the clutch. It fell on the floor!

Shit welds shit piping which is bent and squashed pin holes in the welds and yeah slid into the turbo, probably not even the correct size so I'm. Ot supprised it has soot on the turbo side.

dc848f33.jpg

Dump pipe looks better

c718fc52.jpg

5ed39f78.jpg

Edited by GH05T

The boost line came off my boost gauge, was enough of a leak to make it stall. Kind of makes finding these leaks a pain in the ass., especially if you have multiple not very bad ones.

Edited by Rolls

5 clicks backward on the boost controller and still spiking above 1 bar. What's the best way to do this. Wind it all the way closed an work backwards? How many clicks should it be?

It will run up to 12-13psi with no boost controller if you have a free flowing exhaust.

I bet you have loads of vacuum hose going to it which alone will increase the boost, just remove the controller altogether. I have a turbo shit dual stage bleed valve, even on the lowest setting it would spike to 15psi.

also wtf is "cleaner boost" rofl, I lold irl when I read that.

Edited by Rolls

A boost controller only lets you run more boost than the wastegate spring allows, not less.

So with a stock rb20 turbo with exhaust, front mount etc 10-13psi isn't uncommon "standard" so putting a boost controller on there set to 0 gain will often still run more boost due to the extra length in the lines.

Hence remove the boost controller and I have no doubt it will drop to your desired 1 bar.

Well it seems to have a tendency to backfire or cutout/ missfire when it hits its high boost, which seems to be atm just over 1 bar but it dosnt feel safe holding it at this pressure due to the popping( not always :/ )

also I don't seem to hear my screamer pipe now I think about it... More investigation tomorrow. I took some video of the gauge to see where it got to but u can't hear only of the backfiring or misfiring at top boost, what's actually setting my boost level ATM? The ecu/ Nistune? Fuel delivery? Turbo? I'm confused now, i can't see 16psi being standard?

Also for reference my boost controller

7402095f.jpg

And people still persist in fitting atmo bovs

+1, its impossible to convince people they cause richness, idle issues, hesitation etc etc on an engine with an AFM. The ECU doesn't know WTF is going on when the atmo bov vents.

Well it seems to have a tendency to backfire or cutout/ missfire when it hits its high boost, which seems to be atm just over 1 bar but it dosnt feel safe holding it at this pressure due to the popping

Your still having ignition problems.

what's actually setting my boost level ATM? The ecu/ Nistune? Fuel delivery? Turbo? I'm confused now, i can't see 16psi being standard?

The boost controller. Its possible your fuel pump is NOT keeping up. You may or may not have a factory waste gate actuator. If its factory it is set to 10psi, but it may creep above this to 11-12 psi. If you have an after market waste gate, who knows what the spring rate is. Remove the boost controller all together and see what happens. Removing it wont do any damage. Just plumb from the turbo outlet into the waste gate actuator with some vacuum hose.

Also for reference my boost controller

7402095f.jpg

Ewwww, yuk, old Turbosmart bleed valve. Disgusting, one of these caused me to blow a ring land in my old RB20.

Well it seems to have a tendency to backfire or cutout/ missfire when it hits its high boost, which seems to be atm just over 1 bar but it dosnt feel safe holding it at this pressure due to the popping( not always :/ )

also I don't seem to hear my screamer pipe now I think about it... More investigation tomorrow. I took some video of the gauge to see where it got to but u can't hear only of the backfiring or misfiring at top boost, what's actually setting my boost level ATM? The ecu/ Nistune? Fuel delivery? Turbo? I'm confused now, i can't see 16psi being standard?

UNPLUG THE THING FFS

Your boost level is set by your wastgate actuator spring, however when you change the exhaust this relieves backpressure and also increases it.

Standard with everything stock is 6psi, but with exhaust etc 12-13psi is normal.

Like I said twice before if you have the turbosmart piece of shit even with gain set to 0 the extra length of the lines etc will make it spike to 15psi etc, hence remove it!!!

The popping is because you haven't got an aftermarket ECU and the stock ECU is making it run rich as f**k, your stock coils, old plugs etc can't hack it and hence it misfires.

Conclusion: Remove the boost controller,

edit: google how a turbo wastegate (internal vs external) works and this will help you understand.

Edited by Rolls

Kitto

The fuel pump is a bosh 440 with grt injectors, also a z32 AFM and a nistune ecu

Rolls

chill man i will when i have a chance,

and again i do have an aftermarket ecu, not a stock one. also i understand what your saying but it seems excessive. we shal see when i have time to remove the bleed valve.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...