Jump to content
SAU Community

Recommended Posts

This here is my unopened rb25. Has a surge tank,

044 pump, 750bosch injectors, e85 fuel and an apexi

Power fc. Turbo is a hks 3037 .63 rear housing with a

Garrett front cover. Tuned by smmotorsports making

344.1rwkw on only 15.8 psi. Since October last year

I've done 5 drift events, Phillip island sprints and

Winton Vic time attack over Easter. Engine still has

no signs Of wear.

Hmmmm interesting, my car has tested the limits of that turbo in every way and with a 0.82 rear on the same turbo with every supporting mod possible the best we ran was a 320-330kw...... 344 required 20psi bleeding to 18 and that is with the bigger rear housing!

yeah, I think we can conclude it's a happy dyno, however it's definatley a 300+ car and would be an assload of fun

Yep not doubting that part! It is an awesome combo and tried and tested many times! Good result and welcome to the club haha

  • Like 1

Yep not doubting that part! It is an awesome combo and tried and tested many times! Good result and welcome to the club haha

Good to have people around who are willing to try and test combos so you know what works :D Your car has become a bit of a benchmark for the GT3076R's ability, I reckon!

Good to have people around who are willing to try and test combos so you know what works :D Your car has become a bit of a benchmark for the GT3076R's ability, I reckon!

Well we have found the limit with this combo and will be looking to improve where possible, the 3076 and RB25 were made for each other :yes:

:ph34r: swap it for Hypergears VNT and get 400kw.. do it!! :yes:

Well we have found the limit with this combo and will be looking to improve where possible, the 3076 and RB25 were made for each other :yes:

Edited by AngryRBGTX

:ph34r: swap it for Hypergears VNT and get 400kw.. do it!! :yes:

Not convinced on that as yet! Good result for sure but there are other ways to make power on mid frame turbos! You should know, you are about to try ;)

srsly?

it's written on the chart :P

:laugh:

I know i'm probably going to be shot down in a ball of flames for this.... but is there any real point in shooting for 400?

surely it's just useless power unless you have a very very good and expensive setup

@ 320+ rwkw in a 1.4 tonne chassis I needed to run NT05's just to have a hope of traction, and on your average tyres it was already game over.

seems to me like it's just inviting the motor to pop for power that you will never use beyond a dick measuring contest

I know i'm probably going to be shot down in a ball of flames for this.... but is there any real point in shooting for 400?

surely it's just useless power unless you have a very very good and expensive setup

@ 320+ rwkw in a 1.4 tonne chassis I needed to run NT05's just to have a hope of traction, and on your average tyres it was already game over.

seems to me like it's just inviting the motor to pop for power that you will never use beyond a dick measuring contest

No need for flames, it is a pretty decent comment and something i have also said in regards to my car... My tuner was saying i should go to the 35r frame turbos but i said i was overall happy with the performance....

Overall i think mine needs a little extra spool and maybe more in the top end for drag and long open circuits.... For street and hill climbs i would be running gate pressure anyway so it gives you all options.

My car is only running RSR 265's but once warm i can start to get them to grip up, of course i cant launch the car on them but that is where MT tyres will come into play!

As an all round car to do all events i dont see boost settings allowing 330kw, 360kw and 390kw to be a problem as you cover all bases and still have a damn fast car!

Of course bragging rights too :P You know, coz racecar!

I would love to have more because i can! But the old 3037 has nothing more to give! I will continue to seach for a better way haha

Finally some results. Slap us with a teaser.

Sent from my HTC One XL using Tapatalk 2

Haha yeah some results for you finally! And it went over 500rwhp as planned ;)

Well the meth injection is finally installed after months and months.

Was hoping to join the club but might fall a little short of 300 :(

Looks like the old 2835 pro s is maxing out and we have had to tune to fight off knock rather than outright power.

Back up to JEZ tonight to finish the tune and try a couple of things (cam gear adjustment, adjust afr etc)

You never know, I may get there buy I am a little doubtful.

Well the meth injection is finally installed after months and months.

Was hoping to join the club but might fall a little short of 300 :(

Looks like the old 2835 pro s is maxing out and we have had to tune to fight off knock rather than outright power.

Back up to JEZ tonight to finish the tune and try a couple of things (cam gear adjustment, adjust afr etc)

You never know, I may get there buy I am a little doubtful.

Ah damn! Well i hope it goes well! Shame i hadnt picked mine up from its tune today or i would have popped in and said G'day!

I stay in this club with 390kw :woot:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...