Jump to content
SAU Community

Recommended Posts

is someone telling porkys?

dyno sheet to show it nudged 285 to verify your stat belongs in this thread lol....

maybe you should start another thread for unopened 250-280kw rb25s lllol

It was done at a dyno day with octane booster and a few extra degrees of timing thrown in. Pretty sure it was a generous dyno though.

Will dig up the sheet and post it up.

Haha perhaps i should, didnt mean to cause any harm in this thread :)

283kw at 16.7psi

GT3040 .82 rear housing with 44mm tail gate 6 boost manifold

nismo fuel pump, 660cc injectors

3 inch exhaust from turbo back with 5 inch body cat

Completely stock block

would make more but my dump pipe seems to be a restriction

R33 RB25DET series 2

550cc Deatschwerks injectors.

Shoulda used E85 so I could dick schwiiing in the 300kw club. :laugh:

might wanna look at bigger injectors first man... with a 3076 .82 you could be looking at 340rwkw and that's gonna need 740's

283kw at 16.7psi

GT3040 .82 rear housing with 44mm tail gate 6 boost manifold

nismo fuel pump, 660cc injectors

3 inch exhaust from turbo back with 5 inch body cat

Completely stock block

would make more but my dump pipe seems to be a restriction

Wrong thread, i think you need the 270-284.99rwkw thread....

Or more boost.

297.2kW @ 18psi dropping to 17psi, BP UL98. Will run higher psi after next step of mods.

Stock Manifold

Retuned ECU

Bosch 044 Pump

FMIC

555cc injectors

Splitfire coils

EBC

RB25 High-flowed turbo with Garret internals (similar to 3076, Internal Wastegage, Low-mount)

N1 Water Pump

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeh I think i'll message an old contact i had for ages that manages his own tyre shop now.. n tell him what i want n work with him before ordering..  Got this 17x9 +30 Driftteks on 245/45/17 PSR Drag Radials on the rear.. They fit well - for your reference in future - Rear guards  have been lipped in & minimal to non flaring of the rear Gaurds.    
    • If only it were that easy! I also needed to remove seats, shocks, brake calipers, send my car through a fence, and use measuring and ended up guessing because I didn't remove seats, shocks and brake calipers. It can be hard sometimes Can be a little more complex than 'just measure' if you want to truly measure the entire wheel through all of it's suspension travel. But if you aren't going for every last mm then yeah, you can check the space you currently have and guesstimate.
    • If you own a car, and it has wheels on it, and you know the offset of those wheels, and you have a measuring device, you have everything you need to work out if other wheels will fit.
    • Will this fit? but they are staggered set - RAYS 57DR SEMI GLOSS BLACK 18x8.5 +37 | 18x9.5 +38 5-114.3 STAGGERED SET   or If no go could just get a set 4's wheels of 18x8.5 +37 5-114.3 - would i run 8.5's 235s up front n 245's at the back if I do?   Thanks.        
    • Put a clamp on your return line. I have a feeling it's sucking air, and introducing bubbles to your fuel. With a lot of fuel, less problematic. I'd honestly be redoing all the lines in the tank and clamps on everything.   Also, you've given two different answers to the same question: Asked if being followed by the police you could get down to use the whole tank, you said yes you could, so long as you keep off boost. However, you then followed this up that free revving, it would also cause the issues. I'm doubting free revving is enough to make any noticeable boost on what is likely a decent sized turbo.   So now I have to ask, can you actually drive it lightly and use all the fuel, or does it break up even free revving? Also, have you put a fuel pressure gauge on it? Can you hear the pump change noise at all when you're having this issue?
×
×
  • Create New...