Jump to content
SAU Community

Recommended Posts

UPDATE

Good news: the final shipment has been sent, should be here by no later then Thursday! :cheers:

Bad news: last minute notice from work i have to go away for a conference for 8 days from the 23rd April, so i won't be able to send out anything until i return on the 4th of May. I will pm everyone when i return with final costs and shipping quotes. sorry about this, but im sure the savings are worth the wait :D

  • Replies 221
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

thats ok I guess Im still trying to come up with a way to get these parts in the garage so the missus doesnt see em...

label them as "power tools" ;)

would anyone be interested in FRP parts as well?

im looking at some TS style diffusers, headlight intakes and rear pods, theyre alot cheaper then the CF parts as well which is good :)

Elvis, do an EOI in here :)

List up products and prices.

Best way to do it imo. I am always interested in things, but the price a lot of the time deters me.

Well, put a list up in this thread? If you get enough interest here, then create a group buy thread and if it fails, it fails you close it.

If it works, more people will be interested and drawn in by the title?

Jibberish haha.

Yeah put a list of parts available up, surely it couldn't hurt.

Most people watching this thread will be interested in other possibilities.

Cf or Frp 33 roof spoilers???

Cf dash pieces???

label them as "power tools" ;)

would anyone be interested in FRP parts as well?

im looking at some TS style diffusers, headlight intakes and rear pods, theyre alot cheaper then the CF parts as well which is good :)

Definitely interested in some FRP pieces too. Reckon there'd be some support for them for sure.

Would be very keen for some DMAX style wide guards.

Edited by gtsttrk

hey guys, i will go through everything tonight and PM you all for payment of the remaining balance and give you shipping quotes.

for all who's ordered the OEM R34 wing blades, there might be a slight issue with the design, not sure yet and i have emailed the supplier to see what they have to say. Once i hear from them, i will update this thread with details.

for others who ordered everything else, expect a PM b tomorrow.

Cheers

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...