Jump to content
SAU Community

Recommended Posts

I got hold of a turbosmart boost controller, the bleed vavle style ones, I've put the boost up around 2 - 3 psi and I cant rev past 5000rpm!!!! It pings too much!!!! :ghost:

My mods are:

3" Mandrel bent cat back exhaust

Pod Air Filter

What should I do to recitfy the problem? (Please dont say put the boost back down, coz then it defeats the purpose of modifying it doesnt it! duh!)

Thanks guys!

Link to comment
https://www.sau.com.au/forums/topic/39055-need-help-pinging/
Share on other sites

put the boost back down til you get an intercooler.

or, get an air box to lower your intake temps....

but either way, a 2 psi increase (bringing it to around 9/10psi) causing detonation with those mods is pretty bad.

Link to comment
https://www.sau.com.au/forums/topic/39055-need-help-pinging/#findComment-792763
Share on other sites

what Christian said,

turn the boost down until you get a FMIC and a cold air intake system (either ducting from the front bar into a modified airbox or whatever else you come up with).

whats more important to you??? having a car that drives reliably or a sick hectic motor that'll shit itself sooner rather than later?

Link to comment
https://www.sau.com.au/forums/topic/39055-need-help-pinging/#findComment-793108
Share on other sites

Since you've put it so well - Sick hektic :cheers: - Hahahaha joking joking

Yeh I just found out I've done 15,000kms since buying the car in which I dont know when the Sparkies have been changed so they will be changed soon.

Are Iridium plugs really worth the $16 each asking price??

Link to comment
https://www.sau.com.au/forums/topic/39055-need-help-pinging/#findComment-793124
Share on other sites

yeh mate.

but in all honesty a FULL service should have been the first thing you did when buying the car.. unless there's a log book history of it being done in a reasonable time frame

I had nfi when anything on my car was done so we did everything the week I got it

Link to comment
https://www.sau.com.au/forums/topic/39055-need-help-pinging/#findComment-793136
Share on other sites

If your car is pinging like mad with 2psi extra you've got some *big* problems.

Are you sure its not a missfire? Thats much more common at 5000rpm, do a search, there are heaps of suggestions for solutions.

Link to comment
https://www.sau.com.au/forums/topic/39055-need-help-pinging/#findComment-793256
Share on other sites

From experience, prolonged use of octane boost will stuff your plugs, a real pain especially if you have forked out for iridiums.

As with what Prank said, if you are pinging with such a small increase in boost, that is defiantely a cause for concern and I would bet that there is something else going on. My advice is get the car to a reputable workshop asap for a complete checkup before things really go pear shaped.

Link to comment
https://www.sau.com.au/forums/topic/39055-need-help-pinging/#findComment-794033
Share on other sites

Do a *full* service on it. Including Dyno tune / Power run - FIRST UP.

* Plugs

* Fuel Filter

* Oil Filter

* Air filter

* Oil

* Gearbox and Diff oil too

* Drain & Flush your radiator

* Cheack your fuel pressure

* Make sure you have no vaccuum leaks or pipe leaks - ie intercooler piping etc

Do not attempt to increase boost / power without knowing where you are starting from. ie get a baseline.

Do a compression test / leakdown test also. Just to be sure and for a baseline.

Plan your mods - do them bit at a time and get dyno results between mods.

Do not use octane boost to fix continual pinging.

Report back here with your progress and we will keep advising you.

You should be able to run 2-3 PSI on top of stock without any problems - bit get a bigger intercooler to be sure - a GTR cooler for example.

Hope it all goes well

When all else fails a 50 HP shot of NOS should fix your pinging :D

Cheers,

Link to comment
https://www.sau.com.au/forums/topic/39055-need-help-pinging/#findComment-794824
Share on other sites

Do a *full* service on it. Including Dyno tune / Power run - FIRST UP.

* Plugs

* Fuel Filter

* Oil Filter

* Air filter

* Oil

* Gearbox and Diff oil too

* Drain & Flush your radiator

* Cheack your fuel pressure

* Make sure you have no vaccuum leaks or pipe leaks - ie intercooler piping etc

I would suggest having your timing belt changed also, espically if your car is getting towards the 100,000kms mark.

Are you running an aftermarket boost gauge? sounds like a dumb question... but the stock one is not worth much I found.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/39055-need-help-pinging/#findComment-795224
Share on other sites

I would be careful with that one... I first installed the boost controller (as I just couldn't wait to feel that bigger boost) even though I had the boost guage there ready to go... took it for a spin with what we guessed to be about 0.8 - 0.9 bar, was sitting just off the line with the +7 on the dash. Went like gold, but missed at around 4500-5000 rpm. installed a boost guage and it read 1.45 bar... hence the miss!

Just be careful and even see if you can borrow a guage of someone just to set your boost!

Dan.

Link to comment
https://www.sau.com.au/forums/topic/39055-need-help-pinging/#findComment-796457
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It's not as simple as it is being made out to be. It s not hard, but there are things that have to be done. Am busy right now, but will try to essay later.
    • Pinout is different to my knowledge, but you should confirm to be sure. Also you will need to adjust the VQ table in Nistune to suit. I would still recommend sticking with recirculating BOVs, I'm not sure if the R35 card MAF will fully resolve stalling caused by reversion/throttle lift.
    • What issues are those? Previous owner said it wants to stall sometimes. We did test drive and it was nice and smooth so it will be sporadic or idk. And if i just change MAF(the sensor to R35 version) it should be better? And as i asked...is it like "plug n play" with oem MAF from R34?  This is a MAF from R35 right?
    • Even with no BOV you will have issues unless the MAF is a hot film type like the R35 which has some design features to deal with reversion. Hot wire MAFs are very sensitive.
    • So i just change the (whatever is inside ma original MAF and slide the R34 MAF (it is gonna fit right in? ) and somewhere on the hot side a BoV...i presume that would be vented to the atmo? I just "trying" to understand...maybe my mechanic would know this   I would not mind(even prefer) to run stock BoV cuz it is way more than fine but i do not have that and only pipeing what is left is oem J pipe ... I will be running Blitz fmic(to fit oem one side style) and i gonna need custom pipes cuz i do not have rest of those pipes and hoses... But i am want standalone ECU. Only choice i have atm is Nistune...but that is not gonna cut it right?I dont know what Nistune can and cant do... I know you guys know Link and Haltech...but whatabout ECUmaster? I know guys in here run those but i literally do not know about that and do not know differences... Just know to take whatever "my" tuner can work on.  
×
×
  • Create New...