Jump to content
SAU Community

Recommended Posts

Hey Fellas, i recently had some trouble with my coilpacks, the car was drinking lots of fuel and would get chocked up in high revs i was also getting about 300km per tank of fuel max, i changed the coils to spitfires and the fuel improved to 400+km per tank, and the performance was incredible, so smooth and i can squeeze so much more out of each gear.

now!. i think i can improve my fuel consumption and performance hopefully by changing the injectors. right now i have stock ones and the area around them always looks a bit moist as if they are leaking or something of that nature.

i have no idea about injectors tho and the whole 300cc, 500cc, 1000cc,

What is the stock CC for the R33 s2?

What will give me good fuel economy and performance?

Any good brands?

thanks guys

Link to comment
https://www.sau.com.au/forums/topic/391220-need-some-info-on-injectors/
Share on other sites

Stockers are 370cc. You do know if you go bigger injectors you will need an aftermarket ECU and a tune to suit (1000+).

If they are leaking from the rubber o-ring, you are better off replacing those o-rings.

yeah i have replaced the O2 sensor, didnt seem to do much tho. o-rings and a clean sounds good, since the other options are a bit expensive for now.

i want to do a NIStune but its a bit expensive, anyone had it done??

well i wasnt sure thats why i asked, i know a while back i got quoted around $1300 for a NIStune, so i thought since the coilpacks made such a big diferance at low cost, perhaps better injectors will help also

well i wasnt sure thats why i asked, i know a while back i got quoted around $1300 for a NIStune, so i thought since the coilpacks made such a big diferance at low cost, perhaps better injectors will help also

A good tune is probably the BEST thing you can do for your car. You'll get more power, better drive-ability and a LOT better fuel consumption. I'm making almost 400rwhp and I still get 550kms to a tank. Best I ever got when my car was stock was about 350.

Injectors will do the opposite, if not make your car undriveable without a tune. As Bob said, better off just getting your injectors cleaned and replacing the O-rings. Still highly recommend getting a tune though.

Damn! 550km @400rwhp thats worth a look into, did u get a tune up or get the NIStune thing?

I think you need to understand what people here mean by "tune". It's not like the old days when a "tune up" meant the mechanic would fiddle with all the mixture screws and linkages and pump jets whatnot on the carby, clean/file/replace and set the points and so on. All the little work that made the car's various control systems (such as they were) go back to being in proper spec. In those days your car could get a new lease on life after a tune up because over time all those things would vibrate and wear and block up and so on until they weren't working right.

In a modern car, most of that doesn't happen. Plug leads and plugs may age out and need replacing, throttle bodies might benefit from a clean out, but there's not a lot else that you can do that is akin to a "tune up" from the old days.

BUT......a "tune", now that's a different story. Nissan ECUs aren't reflashable off the factory floor (like many other cars these days are). So the minimum way to make a Nissan ECU tunable is to replace the chip in it with a Nistune board that effectively turns the ECU into a fully realtime programmable ECU. You can do it to pretty much all of them, except the R33 ECU, which you have use an ECU from another car for and do some fiddling. Or, you buy an aftermarket ECU. When you tune the ECU, either just retuning on a stock engine to take out all the extra fuel that the Nissan tune has in it (and make the ignition timing more agressive) or do a complete tune to suit a modified engine, you will make the car use the minimum (safe) amount of fuel for the work it has to do. That's all.

yeah i know what a ture is, its much different from me taking things appart on a weekend and screwing around just because its fun, what i was getting at was did he get the nistune programed into the ECU since it is fairly new or did he go with the regular tune and dyno that every jap car gets whether its a nissan or subaru etc

what i was getting at was did he get the nistune programed into the ECU since it is fairly new or did he go with the regular tune and dyno that every jap car gets whether its a nissan or subaru etc

I still don't think you understand. There is no "regular tune and dyno that every jap car gets whether its a nissan or subaru". What did you mean by that?

And more to the point....he's making 400rwhp.. Of course his car has been tuned. That's not going to happen on an untuned factory ECU now, is it? Whether he has a Nistune conversion in his ECU or he's got an aftermarket ECU really doesn't make any difference to the fact that one way or another, his cas has been "tuned".

Edited by GTSBoy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 馃
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
  • Create New...