Jump to content
SAU Community

Recommended Posts

Hey all just wanted to get some info about exhausts whats a good set up?...ive got an r32 GTR with 280kw ive currently got a stock exhaust I assume for the sound and what not..im after somthing pretty loud but not straight pipe loud and good flow... What size pipe would be best eg dumps??,front?? So forth blah blah

Any info would be greatly appreciated :thumbsup:

  • Replies 57
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Bigger is better for power but obviously you need to quieten it down for the street, and it would depend how low you are as to what size pipe would fit under the car.

There are plenty of 3 or 3.5 inch cat backs available in the for sale section, or you can get me or someone else to make you a full system if you want custom. PM me if you want me to organise a quote or just to drop around for a chat seeing as you're local. :thumbsup:

I've got 34 gtr dumps, and planning on a 3.5 inch custom. Go big, but get proper mufflers, stuffed with rockwool not fibreglass like the jap ones

what front pipes you going?

i got a r32 rb20det, thinking of doing a 3" , no cat, and a chambered? or non chambered? resonator in the middle then a straight jasma muffler. that any good?mellow.gif

im confused are you asking me if that set up is acceptable or is your input to the thread good haha...if your asking if the exhaust is good I have no idea about exhausts but it should be sweet for an rb20 :turned:

then a straight jasma muffler. that any good?mellow.gif

JASMA is a certification meaning the product is street legal in japan. thumbsup.gif

Japanese Automotive Sports Muffler Association (JASMA)

You can tell the brand of exhaust from the 3 digit code on the plate:

Akiyure Inc. 047

Apekusera Inc. 048

Iida Inc. 130

Ikeda industry 003

A tea sea international Japan Inc. 074

Etching k s Inc. 051

Ebansupuranningu asuretsuku division 129

M-TEC Inc. 002

Otoekuze Inc. 120

Automatic backs seven Inc. 097

Ovuareshingupurodakutsu Inc. 124

Katsu Inc. 088

Car land 119

Kind technostructure Inc. 115

Kakimotoreshingu Inc. 017

Garcon division 114

Can tile office 113

5ZIGEN international Inc. 005

Sun automobile industry Inc. 076

Gee earl Inc. 012

Jieiruto Inc. 013

Gee piece Potts Inc. 125

Jiyaosu Inc. 067

Starting line Inc. 069

Spoon Inc. 044

Possession the Suruga Seiki Inc. 106

Zero sports Inc. 100

Tanabe Inc. 026

Taniguchi Inc. 035

Takeoff Inc. 004

Top line Inc. 110

Trust Inc. 006

Knight sport Inc. 019

Huaburesu Inc. 111

Fujita engineering Inc. 061

Rattan ***353;â engineering and research industry Inc. 001

Free way Inc. 123

Buritsutsu Inc. 021

Hoshinoinparu Inc. 037

HONDA twin cam Inc. 011

Mainzuueibu Inc. 038

Makishimuwakusu Inc. 045

Pine Shaw Inc. 008

Meiwa Inc. 041

Yajima industry Inc. 091

Yamato Inc. 122

Lucky automatic Inc. 126

Love lark Inc. 083

jasma cool info. i thought its a brand as well haha. i saw it had trust written on it.

with regards to the cat. i dont care if its legal or not.whistling.gif im looking for an optimal exhaust design flow. not too loud and not restrictive as well. how about a 3" straight deisgn no cats no mid mufflers, just a straight bellmouth muffler on the end? would that work? im only aiming around 280-300hp

anything straight will be pretty damn loud..but again i don't know much about exhaust i was actually hoping to get some info on it as well haha but yer you couldn't get much better flow then straight your neighbours will hate you as well

  • 2 weeks later...

Ideally no u don't want back pressure on a turbo system it can lead to higher exhaust gas temps etc but u don't want to big of an exhaust generally rule thumb work out what power u want and build exhaust to suit of u want 250hpatw build a 2.5inch system . If u want 300hpatw get a 3 " system

Hope that helps bud

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
    • OK, now we are ready to get started. You need to remove the air boxes on each side for clearance. The cover is straightforward, undo the clips on the top and lift the front cover out of the rest of the housing. If it is tight you can remove the air filters first. The rear section of the airbox is trickier. On each side you need to remove the Air flow meter wiring which is held to the airbox with a clip; you need to get behind the clip on 2 sides if you want to remove it without breaking it - unclip the harder side and pull on the clip with medium force, then unclip the easier side and it should pop out The airbox is held onto the intake hose with a spring clamp; you need to get a flat bladed screwdriver behind the spring on both sides and pop them outwards. When you have got them in the right unclipped place they will stay there and the airbox slips out pretty freely. Put a rag in the intake to prevent anything getting dropped in there, and also to prevent you seeing that the turbo seal is leaking oil (as they do). Then. The top of the radiator is held by a steel plate, it is secured by 2x10mm and 2x12mm headed bolts . Remove them and remove the plate Also grab the bushings that hold the radiator to the plate on each side so they are not lost!
    • Next, remove the upper and lower radiator hoses, both are held with a spring clamp. While you are under there, tackle the Auto Trans cooler lines.  Again both are held on with spring clamps, and as mentioned above you should cap them on the radiator side with an 8mm cap, and on the car side loop them with a length of 8mm pipe - this will stop you losing a dangerous amount of AT fluid during the rest of the job If you've been meaning to add a sender for AT trans temp, this is a great time to do it; put a sender fitting into the passenger side line as that is the inlet to the cooler/radiator.
    • Next you need to remove the intake duct (as with pretty much every job on these cars), it is a series of clips you gently remove with a flat bladed screwdriver. They do get brittle with time and can break, and I have not found a decent quality aftermarket one that fits (they are all too soft or flimsy and don't last either) but the nissan ones are a couple of bucks each (ouch).  Once the clips are off (either 8 or 10, I didn't check) you lift the intake duct out and will see the reservoirs Undo the line into the radiator side cap (some bent needle nosed piers are awesome for spring clamps) and then remove the 4x 10m nuts that hold both in place.  I didn't get these pics, but remove the line under the radiator reservoir (spring clamp again) then remove that reservoir. Then you can get at the intake reservoir, same thing, spring clamp underneath then remove it. BTW This is a great time to put in a larger (+70%) combined reservoir that AMS makes..... https://www.amsperformance.com/product/q50-q60-red-alpha-coolant-expansion-tank/ They also make an Infiniti branded and part# version if that is your thing
×
×
  • Create New...