Jump to content
SAU Community

Recommended Posts

hey guys,

took my car to get fuel in the morning yesterday, then washed it. ready for heathcote drag day. we left for the hume highway at 7.30, the car got to the servo fine where we met up with the rest of the cars attending. when we left i started the car all was ok, was travelling down the highway at 100Kmph, then all of a sudden felt the car not shaking but more like a shutter sort of like when you are about to stall it in a manual but all the time...when i accelerated the car would go nowhere untill the turbo kicked in then it JUST dragged the car along...we stopped at a safway on the side of the road, and i turned the car off and back on, and it still done it...i looked under the bonnet and everything seemed ok....i als checked for boost leaks using my gauge, and vaccum and boost was fine...i then turned the car off, left it for a bout 5 mins and turned it back on and it was FINE??!! i still didnt trust it so i left it there all day and went to the drags without it. i came back later that afternoon to grab it and it started fine, drive 50 mins home fine and now runs fine...i cant fault it now??

the car also sort of missfires when i put the foot to the floor at 5000 rpm, but the revvs still keep climbing like normal??? i changed the coilpacks and that helped a LOT, but it still does it under full throttle...its not like a missfire but like a stutter??

can anyone help with BOTH these problems???

cheers!

Link to comment
https://www.sau.com.au/forums/topic/391524-car-playing-funny-buggers/
Share on other sites

  • Replies 46
  • Created
  • Last Reply

Top Posters In This Topic

Id point towards a plug or sensor got wet or the fuel you got had some crap in it. seen as the only 2 things you did was wash it and put fuel in it. it might clear itself up after a drive, don't flog it to much in the mean time

In the boot, remove the back board, you will see 4 10mm screws holding down a plate. Remove that. Under there is a black lid thing with 3 hoses. You want to unplug the wires and get a rag ready for when you remove those lines as fuel is going to come out. Keep the hoses out of the way and take that lid off. To do that get a piece of wood and put it in the notches in the lid and tap it with a hammer to loosen it and get it out. Fuel pump is inside. Plenty of guides here to elaborate and show pictures of how to do it, wire it and fit it back in.

Its not a fun job. Don't do it on a hot day and be ready for swearing. DO NOT EVER attempt to do it with more than a quarter fuel in the tank. Hell run it to near empty if you can.

Fuel pump isn't that hard if you get a good one. my tomei pump was easy as. pull the old one out, drop the new one in

This. Took me half an hour, including diagnosis of why the car wouldn't start when I reversed the polarities :P

Agree with running the tank near empty first though. Arms get real damn itchy immersed in petrol ermm.gif

Edited by Hanaldo

This. Took me half an hour, including diagnosis of why the car wouldn't start when I reversed the polarities :P

Agree with running the tank near empty first though. Arms get real damn itchy immersed in petrol ermm.gif

And in a hot day, that itch plus the humidity rising from the fuel tank is enough to really f**king frustrate you when you cant get that cradle in the bracket.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Old Son, did you re-use the Holden ABS in the new shell or try a different module?
    • Yeah, nah. I had the actuator rod off it today. The arm will not move at all. Neither out, nor in. Yeah, you'd think so, but I've been thinking about that. Even when the actuator rod fell all the way off at the beginning of this saga, it would build more boost and faster in lower gears than it would in higher gears, and you'd think that that was the opposite of what should happen. But I strongly suspect that there is a thing with the gearing getting the revs to rise faster, that there must be some transient effect with the gas flow rate rising quickly, that you don't get with the more steady state case of the higher gears. Keep in mind - the gate is not shut in either of my weirdnesses. So things are not "normal". We normally think about a turbo spooling up (below the wastegate target) with the gate shut. I have all sorts of mental models running now where the gate is a little bit open, and having it stuck open allowing gas out while it should be going through the turbine has all sorts of weird effects (in these mental models). I'm thinking in the higher gears, the ex mani pressure builds to the point where enough gases spill out the wastegate to just prevent the pressure rising much more at all, or just creeping up, all the whole the revs are increasing and getting closer to the point where a gear shift becomes necessary.
    • Is it possibly wastegate actuator itself is sticking, or even the rod to flapper? Otherwise I reckon things are getting a bit rusty/worn   Also odd it won't boost in 3rd to 5th, but will in 1st, I'd expect the other way around with it slightly open as there's more time on your way to redline for it to spin up
    • Does anyone know ow what these two plugs are for and if they should be unplugged? Just put the dash back together and can't remember if these were plugged in before or unplugged! (Blue and white plugs) 🤦🏽‍♂️
    • Did some FASTing ...got the impression that the actual part# was a moot point ; seems all of these hardlines for coolant are discontinued/NLA... like, I take it you're after the hardline that bolts onto to the manifold...that's NLA according to amayama & nengun .... ...just to clear up some confusion, they typically mounted the AAC valve to the intake manifold somewhere near a coolant passage, so the body of the valve heats up & holds it open when engine's up to temp - no coolant flows through the valve, it's a mechanical, thermal connection.
×
×
  • Create New...