Jump to content
SAU Community

Recommended Posts

Now, I was actually on the phone to Bec this morning about booking in a defencive driving course and got on to the topic of mods for P platers.

I'm really not sure what the rules are. My current understanding is that a P plater is not allowed to do ANY engine mods at all. My understanding was also that if the car came with mods already it was fine, it was just DOING mods was an issue.

I tend to agree with Bec that it's most likely that I'm incorrect. SO! I understand there's a cop or two apart of the forums, I'm eager to hear what the actual rules are, more out of curiosity than want to actually mod, as I don't have the spare $$$ to do that anyway.

Thanks,

Teir.

Link to comment
https://www.sau.com.au/forums/topic/392644-p-plate-legal-mods/
Share on other sites

no mods allowed, pre or post purchase, go to vic roads web site and find the facts, dont listen to people on forums, there not going to take your points or fine for you when there wrong!

Power mods are illegal.

http://www.vicroads.vic.gov.au/Home/Licences/GetYourPs/RestrictionsOnPs/Pplatedriversandprobationaryprohibitedvehicles.htm

has an engine that has been modified to increase the vehicle's performance (other than a modification made by the manufacturer in the course of the manufacture of the vehicle, or

Given the exhaust is attached to the engine, and it's all one system.

However it does not say suspension, brakes etc. So those would fall under normal guidelines.

Bah, oh well. That sorts that out :-)

Though here's a good question, would that include changing the coil pack? I know obviously there's no way a cop could possibly know if you had, but just for arguments sake, would installing splitfires in my R34 GTV classify as an illegal engine mod since it's not the original manufacturer's part and is said to increase performance (though scoffed at by some)?

Would I technically have to replace the coils with the original parts from nissan?

-Teir

if you're willing to take the risk that the copper doesn't know. then you probably can get away with it.

although i wouldn't recommend you spend any money on the car really, but if you definitely have to, then exhaust, a better flowing air filter, and be happy till you're off your p's.

anything more presents too much of an investment with no real gain imo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...