Jump to content
SAU Community

Recommended Posts

  • Replies 107
  • Created
  • Last Reply

Top Posters In This Topic

Dinky dye effort, hey steve :cheers:

Who needs bigger turbo(s), 4wd systems, head work, non-standard bottom end.....etc etc...

:D I'm stoked to have realised the potential of the car in it's current form.

BIG thx to the BU5TER for the use of the Nittos. What wonderful tyres they are!!!

Adrian

u must be still on a high.... so u better keep that form and go hard until the wee hours af the morning champ ahahah :cheers:

do u reckon there will be pics.....i would like to see one of u doing the trade mark thumbs up burn out and one of busters face side by side aahahahah

that is awesome!!!! what clutch do you have and what rpm did you launch at for that 60fter!!?

Heavy duty Excedy single plate. 4-4500rpm launch, slipped for a tenth of a second then got off it all together. Gas off the line pulls hard!

Adrian

congratulations champ, hm those nittos sound awsome i think i need some, ill be heading back there in a month or so, need to get the nos kit in, what shot were u using for the nos kit, still the same as befor?

As I posted in the SAU Drag V2 thread - awesome result Adrian! Well done mate.

It's amazing the HP gain that a small shot of nitrous has given you! 117+mph takes a fair bit of grunt.

If you managed a 1.6 60' on Nittos then there's hope for me to get a 1.8X on my 275 Nittos yet :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...