Jump to content
SAU Community

Recommended Posts

Hey guys im looking to sell that set of Sparco? wheels they are in decent condition only 1 seems to have guttered. they are a bit dirty been sitting in my garage for months. 2 of the rims have got decent rubber on them 2 of them rubber is stuffed.

they are 16x8 looking for $150.

Also selling that nismo steering wheel want $50 ONO for that (includes boss kit)

Also got some bright blue seat covers that someone can have for free if they come pick them up.

ALSO i know this isn't the place but im selling 1 160gb PS3 (used 1 time) and 2 wii consoles.

Ps3 $250+7 games, assas creed revalation $50

WII $70, Wii fit $50 (with board)

im an ex EB manager so i got all the games and stuff for free.

PM me if you want any of it.

post-92069-0-55321000-1331096988_thumb.jpg

post-92069-0-70011200-1331097019_thumb.jpg

post-92069-0-38836200-1331097146_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/393998-fs-16-sparco-wheels-and-other-stuff/
Share on other sites

Wheels gone, still got the steering wheel and those lovely? seat covers, can take a photo if you want. also all consoles still here.

Also got a question, does anyone know how much a full set of original floor mats for an R32 GT-R go for these days?

My mate had the exact same wheels on his R31, needed 10mm spacers on rear, and 5mm on the front to clear the spring seat.... But coilovers are a good solution for that!

I'll take the Nismo wheel, might suit my HR30 Coupe nicely...

PM me you contact details (I'll be back from training on Sunday next week...)

R32 GTR original full set of mats (5) - yeah I can do that. They'll need a steam clean but in good nick for 22yo's.

A full set new you will need to sell your woman for them.

Nismo for the R32 GTR about $400 from memory. maybe a bit less.

PSIII you say - hmmmm

Anthony or Anne Fanny (j/ks) :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...