Jump to content
SAU Community

Recommended Posts

1: enkei rp01 17 x 9 +22

just had them resprayed silver (matched to the original colour). There was some pitting you can see through the paint that they didn't fill in. They look nice from a couple of metres away.

$900 + $50 postage Australia wide.

enkei rims

2: Garret turbos for a GTR. 2860 -7 I believe.

Just rebuilt by Precision Turbos. Both have brand new bearings and the exhaust housings have been ceramic coated in black. As good as new.

Part numbers from the cores:

HH 0110J

14411-AA403

707160-7

Part number from actuators:

430819-369

08223

35367

$1600 + $50 postage (includes insurance)

turbos

3: R32 GTR Fibreglass front diffuser

The one in the link is the one I bought

R32 GTR diffuser

$220 + $25 postage

4: Speedline 17 x 9 +25

Tyres are dead but may pass rego. I lost one centre cap on the road :( Comes with the centre cap tool too. :)

usual small gutter rash

$400 + $50 postage

speedline

5: 4" stainless exhaust

Front pipes to back

only used for a short time by previous owner, catco cats on each leg of the front pipe. Will need to be welded back together. I cut it up to squeeze it in my car.

$400 can be posted but unsure of postage costs.

exhaust

6: r32 GTR side skirts 2 pairs

both need straightening and one set needs painting, the other needs a GOOD polish

just take them.

7: RB26 block with rods pistons and crank (pistons and rods removed from block)

no cracks, all is in good nick.

$200

8: R32 GTR Tomei dumps, the older fabricated ones BRAND NEW AND UNUSED

ceramic coated black, will accept only the R32 GTR 02 sensors. provisions for exhaust temp sensors on both pipes

$600 + $15 postage

tomei dumps

9: used aftermarket rb26 manifolds not sure on brand, no cracks, provisions for heat shields

ceramic coated black

$200 + $20 postage

manifolds

10: used rb26 heat shields ceramic coated

$80 + $15 postage

heat shields

11: R33 GTR aircon compressor sold as is

$50

air con compressor

12: R33 GTR standard clutch, flywheel and pressure plate USED

$50

clutch

13: N1 water pump used

$50 + $12 postage

14: N1 oil pump used, not cracked

$50 + $12 postage

15: ex BSM R32 GTR sump, with baffles and extended pan

needs a donor sump for the diff parts

$850 + postage

sump

16: standard r32 gtr sump good condition

$200

17: ex BSM R32 GTR Quaife front diff centre used but in good condition

$1200

quaife

18: tomei pon cam replicas bought from dirtgarage (who used them for a short time) then not used by me.

260in 260ex 9.15mm lift

$400 + $20 postage

19: R32 GTR fibreglass N1 bonnet lip painted in white NEW

$80

lip

20: R32 GTR fibreglass N1 boot lip painted in white NEW

$160

lip

21: R32 GTR Trust style fibreglass rear pods painted in white NEW

$160

pods

Will post at buyers expense. Pick up is available from Quakers Hill.

Cheers

Josh

Link to comment
https://www.sau.com.au/forums/topic/394428-skyline-parts/
Share on other sites

  • 2 weeks later...

1: enkei rp01 17 x 9 +22

just had them resprayed silver (matched to the original colour). There was some pitting you can see through the paint that they didn't fill in. They look nice from a couple of metres away.

$900 + $50 postage Australia wide.

enkei rims

2: Garret turbos for a GTR. 2860 -7 I believe.

Just rebuilt by Precision Turbos. Both have brand new bearings and the exhaust housings have been ceramic coated in black. As good as new.

Part numbers from the cores:

HH 0110J

14411-AA403

707160-7

Part number from actuators:

430819-369

08223

35367

$1600 + $50 postage (includes insurance)

turbos

3: R32 GTR Fibreglass front diffuser

The one in the link is the one I bought

R32 GTR diffuser

$220 + $25 postage

4: Speedline 17 x 9 +25

Tyres are dead but may pass rego. I lost one centre cap on the road :( Comes with the centre cap tool too. :)

usual small gutter rash

$400 + $50 postage

speedline

6: r32 GTR side skirts 1 pair

both need straightening and one set needs painting, the other needs a GOOD polish

just take them.

7: RB26 standard rods pistons in excellent condition

no cracks, all is in good nick.

$100

9: used aftermarket rb26 manifolds not sure on brand, no cracks, provisions for heat shields

ceramic coated black

$200 + $20 postage

manifolds

11: R33 GTR aircon compressor sold as is

$50

air con compressor

12: R33 GTR standard clutch, flywheel and pressure plate USED

$50

clutch

13: N1 water pump used

$50 + $12 postage

15: ex BSM R32 GTR sump, with baffles and extended pan

needs a donor sump for the diff parts

$850 + postage

sump

16: standard r32 gtr sump good condition

$200

18: tomei pon cam replicas bought from dirtgarage (who used them for a short time) then not used by me.

260in 260ex 9.15mm lift

$400 + $20 postage

19: R32 GTR fibreglass N1 bonnet lip painted in white NEW

$80

lip

20: R32 GTR fibreglass N1 boot lip painted in white NEW

$160

lip

21: R32 GTR Trust style fibreglass rear pods painted in white NEW

$160

pods

Will post at buyers expense. Pick up is available from Quakers Hill.

Cheers

Josh

Items updated

Link to comment
https://www.sau.com.au/forums/topic/394428-skyline-parts/#findComment-6303499
Share on other sites

  • 2 weeks later...
  • 3 weeks later...

1: enkei rp01 17 x 9 +22

just had them resprayed silver (matched to the original colour). There was some pitting you can see through the paint that they didn't fill in. They look nice from a couple of metres away.

$900 + $50 postage Australia wide.

enkei rims

2: Garret turbos for a GTR. 2860 -7

Just rebuilt by Precision Turbos. Both have brand new bearings and the exhaust housings have been ceramic coated in black. As good as new.

Part numbers from the cores:

HH 0110J

14411-AA403

707160-7

Part number from actuators:

430819-369

08223

35367

$1600 + $50 postage (includes insurance)

turbos

3: R32 GTR Fibreglass front diffuser

The one in the link is the one I bought

R32 GTR diffuser

$220 + $25 postage

7: RB26 standard rods pistons in excellent condition

no cracks, all is in good nick.

$100

9: used aftermarket rb26 manifolds not sure on brand, no cracks, provisions for heat shields

ceramic coated black

$200 + $20 postage

manifolds

11: R33 GTR aircon compressor sold as is

$50

air con compressor

12: R33 GTR standard clutch, flywheel and pressure plate USED

$50

clutch

13: N1 water pump used

$50 + $12 postage

15: ex BSM R32 GTR sump, with baffles and extended pan

needs a donor sump for the diff parts

$850 + postage

sump

16: standard r32 gtr sump good condition

$200

18: tomei pon cam replicas bought from dirtgarage (who used them for a short time) then not used by me.

260in 260ex 9.15mm lift

$400 + $20 postage

19: R32 GTR fibreglass N1 bonnet lip painted in white NEW

$80

lip

20: R32 GTR fibreglass N1 boot lip painted in white NEW

$160

lip

21: R32 GTR Trust style fibreglass rear pods painted in white NEW

$160

pods

Will post at buyers expense. Pick up is available from Quakers Hill.

Cheers

Josh

Link to comment
https://www.sau.com.au/forums/topic/394428-skyline-parts/#findComment-6344103
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...