Jump to content
SAU Community

Recommended Posts

doh, i just bought 8000k for mine- very blue

Is that illegal or something?

Not overly fussed about visibility as its a city car in perth. It doesnt rain much n u could also drive with your headlights off half the time n not notice with the street lighting...

Thanks guys

I've done a bit of research into the topic. 4300k is the closest to daylight colour and after that they start going blue. Most OEM's use 4300k globes but the most popular aftermarket colour is 6000k.

The most contributing factor is the type of headlamp they go into. Cut glass lenses (the old school type) tend to throw the light around. This is because hid light output is very directional and refracts easily. The best lamps are the projector and free form designs. They control the light much better and give a defined cutoff. Important so your not blinding oncoming cars.

Cheers

4300K is light yellowish, 5000k close to white (will look slightly off if you have white LED parkers), 6000k is white, will match white LED parkers the best and probably the highest you'd want to go for looks vs. visability. Anything higher tends to blue/purple and will be worser off for visibility.

I have 6000k in my HR31 and now R32 and are absolutely awesome :). Just make sure they are not aimed too high and blind other road users. Also if you are going to use them in non-projector type headlights you should probably get a Hi/Lo type kit as you will blind people no matter where you aim them ;)

Edit: Added a pic of my conversion half done.

post-27061-0-01867800-1333590863_thumb.jpg

Edited by ColdFusion

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys . Can someone help me  I bought an Android screen for my Nissan fuga but it won't turn on   
    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
×
×
  • Create New...