Jump to content
SAU Community

Recommended Posts

Hey guys,

Just wanting to know if anyone has had a spare key programmed in Brisbane? I have gone to Nissan on the magic mile but they told me that if they tried to program the transponder that my other key may stop working as well.... I heard that there is another way around this by just cutting the wire to the original security system but I was wanting to keep everything in tacked if possible, is it really that hard to program another key?

*I have a apexi power FC installed in my GTR and not the original ECU

Thanks!

Tommy

Instructions for programming a factory immobilizer key are in the r34 supplemental manual ( on the skyline uk forum or scribd website) but you better know what your doing its easy to screw it up

No need to cut any wires.

Talk to Chris above.

If your new key is just a blank, copy it first before its programmed.

And take it to a locksmith who can punch in the code from your primary key onto the computer. That way you'll end up with a proper original rather than the edges possibly becoming a worn copy.

Then see Chris above

  • 3 weeks later...

From memory - doesnt having an aftermarket ECU cut out the NATS?

You may be able to use a standard cut key without the transponder in it.

To correct myself above.

I just bought a new genuine key and yes, i had to have it programmed before for use.

  • 1 month later...

Thanks guys!

Can you please let me know the place you got this done, having some issues finding a place. lot of locks smiths that used to do it, seems not to do now for some reason.

Thanks a bunch in advance....

Hate having 1 KEY and 1 Black IMO.

  • 2 weeks later...

I got mine done today and very happy with it.

got it done via these guys in 20min

Millennium Locks

57 Wellington Rd

East Brisbane QLD 4169

07 3177 3680

http://millenniumlocks.rtrk.com.au/?scid=64623&kw=4768069&pub_cr_id=5278493270

This is after lot of wasting time with few places and a hopeless visit to Nissan Mt Garvett, who after accepting the car for procedure, backed away.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
    • The annoying part about neglect, is when you start to replace one thing, and find ten more broken things. Ham fisted monkey repairs you normally only find out about when trying to do something unrelated! Ha ha   Neglect you can kind of anticipate the huge costs to fix it all. Ham fistedness is normally a shock the first time your work on a new old car, as everything "looked" good before.
    • For DBA, check out their guide table here. https://dba.com.au/wp-content/uploads/2023/01/Direct_Replacement-Guide-2021.2.pdf   Additionally they have some other guides and info on how to make sure you choose the right pad.
×
×
  • Create New...