Jump to content
SAU Community

Recommended Posts

Okay so here goes, started my car one morning and it ran fine warming up but as soon as i took off the car started miss firing and running like sh*t. Thinking my plugs had finally given up i replaced them with bpr7es (they were NGK iridium ones gapped to 1.1) the new ones still miss fired. I've also replaced all my coil packs with ones that are known to work. Also cleaned the AAC valve and replaced the fuel filter thinking it was fuel related. The car still miss fires and i am out of ideas on what to test or look for next. Also reset the ecu and no change.

Car has full 3' exhaust, FMIC, Electronic boost controller set to 10 psi, Apexi pod filter.

Any ideas on what to check or look at next are much appreciated!

Daniel

Link to comment
https://www.sau.com.au/forums/topic/397519-rb25-miss-fire-saga/
Share on other sites

Plug gaps should be 0.7-0.8mm. Iridiums are crap plugs too. Coppers are fine.

Gap the plugs down and I can almost guarantee the miss fire will go away.

If not, it's time for a set of split fires.

Not exactly true. Nissan never had a problem with them. Iridiums may be the cause of problems for a lot of people with modified skylines but that doesn't make them a crap plug.

Also to the OP: They should be BCPR6ES unless you are making over about 400-450hp at the wheels

Not exactly true. Nissan never had a problem with them. Iridiums may be the cause of problems for a lot of people with modified skylines but that doesn't make them a crap plug.

Also to the OP: They should be BCPR6ES unless you are making over about 400-450hp at the wheels

You are right, but the reason I think they are a crap plug is because they are expensive and give no more value than copper plugs.

I put a set of brand new set of BCPR6ES in this morning and still miss firing, the plugs i put in previously were gapped at 0.8mm

Anyone think dry solder joints in the air flow meter might cause this?

And it miss fires constantly, under acceleration and at idle.

Got the multimeter out for a couple hours this afternoon and couldn't find anything out of the ordinary.. Think it's almost time to send it to the Auto Lecky.

Nah. If it is missing all the time it will be ignition or injector. You will need to go through and diagnose the lot. Start by pulling coil loom plugs to see if you can isolate which one is not going. Then try to work out if it is sparks or fuel. Remember, looms, connectors and pins all fail as well as the devices at the ends thereof.

Edited by GTSBoy

That is why i put a whole set of coils in that are known to work and it's still missing, might pull my injectors out and flow them tomorrow at work if i get a chance.. Other than injectors though, there's not much else it can be.. right?

Hmmm. Perhaps read what I wrote about the loom and connectors etc again. It's not just devices that fail.

Had exact same issue, got car back late last night. Was the ignition module. Have splitfires and they were fine, block is only producing 2/3rd of rated power (built for) - compression all good. Checked vacuum hoses etc, cables etc. Thought it may have been the 040, but it primed for the 3-5 seconds once ignition on.

So would say check AFM, if not AFM get ignition module checked pending the plugs have been changed/gapped etc.

I had the injectors flowed at my work this morning and one of them flowed almost nothing, the others were all below what they should have been as well.Changing the baskets and sonic bathing them monday, really hoping this is what was causing it!

Thanks for all the advice guys!

Daniel.

Had exact same issue, got car back late last night. Was the ignition module. Have splitfires and they were fine, block is only producing 2/3rd of rated power (built for) - compression all good. Checked vacuum hoses etc, cables etc. Thought it may have been the 040, but it primed for the 3-5 seconds once ignition on.

So would say check AFM, if not AFM get ignition module checked pending the plugs have been changed/gapped etc.

Just to add. my 040 primed ok, car idled ok and would rev ok under no load but as soon as it was in gear and under the load is when it wasn't holding any presure so although you have found an issue with your injectors, if it doesn't fix it don't rule out the pump or pressure reg until u have had it all tested.

Edited by FordyR31

Just to add. my 040 primed ok, car idled ok and would rev ok under no load but as soon as it was in gear and under the load is when it wasn't holding any presure so although you have found an issue with your injectors, if it doesn't fix it don't rule out the pump or pressure reg until u have had it all tested.

As soon as it's all back together i'll get the fuel pressure gauge on it and check pressure at idle and under load just to make sure. I'm just curious, How long did you have your 040 before it gave up like that? I'm thinking about upgrading to one eventually and just wondering about reliability?

Thanks again! Daniel.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for all the replies fellas. Gonna finish putting it back together and see how it handles the set up. If it starts pinging it’ll be parked.
    • Well, I can recommend the partial AV system translation CD I ordered from Car Audio Workshop in NZ. Whilst it didn't address the date issue, it has conveniently translated on-screen menu items into English, and now allows the GPS-received time to be offset in hours rather than minutes, so I can display Eastern Australian time accurately ( and bump it by another hour when daylight savings starts ).
    • Yuh, if it's 45°C outside, my car is driving in it.
    • I'd be curious to hear more. Otherwise, have you driven a modern x-trail? I wonder how it compares. Here in Australia they are/were popular for rentals and fleet vehicles. I have been in some and my impression was they are bad. But, this may have been very different in the 2000s at a good trim level. Twenty years is plenty of time to make the model worse. I do very much agree with the 2 silver cars in the garage approach. But, not driving because it's too hot would not leave a lot of time in the year for many Australians. I don't think you need to worry too much unless the car has actual issues with overheating. 
    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
×
×
  • Create New...