Jump to content
SAU Community

Recommended Posts

So I replaced my ceramic button clutch with a streetable heavy duty organic.

In the process I replaced the spiggot but did not replace the input shaft bearing

(I think that's right, when I depress the clutch stationary it gets noisy as hell, clutch in quiet)

My question is what will happen if this bearing goes unchanged for a while?

I won't be able to pull the gear box out gain any time soon. What will the actual effects be? Or will it just be noisy? It's loud but I feel no actual effects.

Link to comment
https://www.sau.com.au/forums/topic/397688-will-the-bearing-do-damage/
Share on other sites

If it is the input shaft bearing, if you keep driving it the bearing will eventually collapse and quite possibly wreck a gear or 2 costing you more in the long run. Did you replace the clutch throwout bearing that sits on the fork?

Sounds like you mean the throw out bearing, which is the one that the clutch pedal pushes onto the pressure plate. Here's mine;

med_gallery_15274_3064_69219.jpg

The clutch kits i've seen all come with one. Just change it. Eventually it will fall to pieces and you wont be able to release the clutch.

Hang on OP, you said the noise is there when you depress the clutch and it disappears when the clutch is in...these are one and the same, so which is it?

Foot on the pedal pushing it in...is the sound there?

Foot off the pedal...is the sound there?

Which one comes with an exceedy clutch kit? Spigot?

Nope, the throw out will always come in a clutch kit. Throw out should always be replaced when you do the clutch, spigot is often ok. If the throw out is dead it will squeal when you push the clutch pedal. Spigot is the bronze copper ring in the center at end of the crank;

med_gallery_15274_3064_132065.jpg

Hang on OP, you said the noise is there when you depress the clutch and it disappears when the clutch is in...these are one and the same, so which is it?

no. "depress" means you are no longer pressing in, and when the clutch is in, as in you "press" the clutch in, it goes away, make sense?

http://www.thefreedictionary.com/depress

Was the noise there before you installed the new clutch? What kind of noise is it, a whine/grind/squeal/rattle? Which bearing did you replace, spigot or throw out (see MrStabby's pics).

  • 2 weeks later...

no. "depress" means you are no longer pressing in, and when the clutch is in, as in you "press" the clutch in, it goes away, make sense?

To depress the clutch pedal means to push it down. You can't just make up your own definitions - you'll just confuse people.

So to press my clutch means to let it out ?

Does anyone have an answer to which beating that is instead of more insights to a specific word? I even put a video showing the clutch position can we move on?

I wouldn't assume oil as the gearbox is not moving but more a bearing inline with the clutch,

Is that most likely the thrust bearing?

So to press my clutch means to let it out ?

Does anyone have an answer to which beating that is instead of more insights to a specific word? I even put a video showing the clutch position can we move on?

I wouldn't assume oil as the gearbox is not moving but more a bearing inline with the clutch,

Is that most likely the thrust bearing?

I'll start off with my usual disclaimer, " I'm no Mechanic but "

It is my understanding that when you are sitting still with the car running in neutral with your foot off the clutch ( I'll avoid the press-depress issue :rolleyes: ) the input shaft is obviously turning at the same speed as the flywheel and so is other stuff in the box, so I'd take on board what turboedsloth says I'm pretty sure he rebuilds gearboxes :thumbsup:

does sound a bit raspy to be throw-out bearing,,,, could wrong,, either way its box out

Yeah box will come out, I guess it's good practice to replace both the throw out - input - thrust bearig just do it all for the sake of doing it while were in their. Are any of them specifically difficult

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
    • Well they got my money but they are not getting my gearbox ! 
    • It's needed for rolling idle up, and I think it is a decider on VCT also.
    • I mean, not really. Link ECU's can absolutely still have errors from the ECU thinking it's getting a sensor it's not expecting. I would imagine the speed at the ECU level in Nistune does absolutely nothing anyway? I assume the ECU does not do any fancy TC stuff with regards to front+rear wheel speed or anything of that like anyway. Someone who uses Nistune may be more fluent in it. 
×
×
  • Create New...