Jump to content
SAU Community

Recommended Posts

Well Scott's did 13.9 with more power. It's getting the barges off the line that counts. I have no doubt he would demolish mine in a roll on.

Hope you can stall it up with boost. Will be fast if you can.

Not likely, it wont even start. lol.

Luckily I got it going to get it off the dyno and onto the car trailer, when I got it home the damn thing was hydro-locked. Off with the heads next week for a check, if all's good I will replace the head gaskets, fit the ARP L19's and try again.

nice work guys, i was planning on running tomorrow but weather is shocking so ill have to wait till a day where its clear lets see waht stock power vs. now 300kw does

Yours will be a very interesting run mate, I wouldn't be surprised if you can get into the 12's with better tyres. Lighten it up as much as you can... :)

  • Replies 179
  • Created
  • Last Reply

Top Posters In This Topic

Best I could do was back up my 12.3,

Clutch didn't seem to like 300+kW+Drag launches+fat heavy car and is now rather f**ked.

I wont be buying another exedy clutch as it only lasted 9 drag launches and 10k km of fairly sensible street driving most of it on 280kW.

DVS JEZ what would you suggest? Car isn't driven daily and pedal weight is less of a concern but i would like to maintain some feel and not go back to the on/off switch HKS twin plate i had in it.

Edited by numleg

Sounds all to familair.....I have done 2 trips to the drags and done 2 clutches.....both were built by Race clutch

The 2nd one I killed actually had its last day on the street. It fused the carbonic clutch plate to the flywheel

and would not dis-engage. 4200lb single plate

I have just had a complete new clutch and billet flywheel installed. The factory flywheel was in bad shape with a blue heat ring around around the face where the linings ran. Clutch is a NPC this time. Will see how long it lasts...

The car is arount 1650kg

Trap speed was consistantly 185kph+ this should be good for a 12.00 or faster.

best 60 foot time was 1.8

This car won't see track time only street and drag. I have a 180 for track/drift/stupidshit.

I'm looking at what i can get local today otherwise i will order the nismo compermix comp $2200 from RHD Japan delivered isn't too bad but thats still a lot of cash.

My GTR runs an exedy cushion button twin plate. Even my missus can drive it. Has seen alot of abuse and circuit racing.

How much does ur car weigh?

Wht MPH did u run?

Edited by numleg

The car is arount 1650kg

Trap speed was consistantly 185kph+ this should be good for a 12.00 or faster.

best 60 foot time was 1.8

This car won't see track time only street and drag. I have a 180 for track/drift/stupidshit.

I'm looking at what i can get local today otherwise i will order the nismo compermix comp $2200 from RHD Japan delivered isn't too bad but thats still a lot of cash.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...