Jump to content
SAU Community

Recommended Posts

Hey S.au need help with my gtr -__-

car runs like a shitbox especially when is warmed up!

car will miss and broad minded personter and wont rev past 2,600 feels like its a tune issue .. not a coilpack miss or spark miss but an electronic part shit itself f**king my shit up

had issues with air flow meter ... when it was warmed up 1 AFM was causing it to stall when hot ... replaced the faulty AFM now just runs shit house but runs -__-

timing has been checked .. throttle position sensor doesnt cause survere symtoms im having .. coolant temp sensor was recently replaced (ecu type)

any1 have ideas on what would cause this ?

any1 know any good import mechanics preferably with scan tester in brisbane southside?

cheers S.au f**k piggs!!!

Link to comment
https://www.sau.com.au/forums/topic/397906-engine-problem-with-rb26-r32-gtr/
Share on other sites

car doesnt shake heavily .. although it could possibly be 1 cylinder down =/ or head gasket issue ( hope not though ) dont have comp tester or TK tester

hope its just some sort of sensor fault ... ecu shit itself ? common problem =/ ???

I've got Nissan data scan and I live in Ipswich/work at Richlands if you would like to see if the self diagnostic has anything to say.

diagnostic scanner would be choice !! when are you free ? would be much appreciated!!

It still sounds like an AFM issue. Do u have 2 known working ones u can borrow off a mate or sau friend.

Where are u located

Southside brisbane Forestlake

originally had AFM issue .. 1 was causing it to stall .. replaced that 1 and it stopped stalling ... but runs like shit =/

when i change the other AFM with the 'faulty' 1 .. car stalls again *thinks* dam 26s

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...