Jump to content
SAU Community

Recommended Posts

Hey S.au need help with my gtr -__-

car runs like a shitbox especially when is warmed up!

car will miss and broad minded personter and wont rev past 2,600 feels like its a tune issue .. not a coilpack miss or spark miss but an electronic part shit itself f**king my shit up

had issues with air flow meter ... when it was warmed up 1 AFM was causing it to stall when hot ... replaced the faulty AFM now just runs shit house but runs -__-

timing has been checked .. throttle position sensor doesnt cause survere symtoms im having .. coolant temp sensor was recently replaced (ecu type)

any1 have ideas on what would cause this ?

any1 know any good import mechanics preferably with scan tester in brisbane southside?

cheers S.au f**k piggs!!!

Link to comment
https://www.sau.com.au/forums/topic/397906-engine-problem-with-rb26-r32-gtr/
Share on other sites

car doesnt shake heavily .. although it could possibly be 1 cylinder down =/ or head gasket issue ( hope not though ) dont have comp tester or TK tester

hope its just some sort of sensor fault ... ecu shit itself ? common problem =/ ???

I've got Nissan data scan and I live in Ipswich/work at Richlands if you would like to see if the self diagnostic has anything to say.

diagnostic scanner would be choice !! when are you free ? would be much appreciated!!

It still sounds like an AFM issue. Do u have 2 known working ones u can borrow off a mate or sau friend.

Where are u located

Southside brisbane Forestlake

originally had AFM issue .. 1 was causing it to stall .. replaced that 1 and it stopped stalling ... but runs like shit =/

when i change the other AFM with the 'faulty' 1 .. car stalls again *thinks* dam 26s

  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Waaay ahead of ya....(evil laugh!!) Will show the fitment and spec details later when it isnt as rainy !
    • Thanks Dose.....    I appreciate it!!
    • I'll probably be putting the shit box back on the dyno again soon, I want to dial in the closed loop boost control properly. I'll have a camera facing the car/motor for fun too. Just note, there are essentially 3x 10AN inlets going into the catch can and 1x going back to the intake pipe. Most of the time the catch can "return" to the sump actually is the crank case breather, pushing air out.
    • I have the R3C with a Nismo slave and by no means does it behave like a stocker, it ain’t THAT bad. On take off just give a bit more throttle than you would say a coppermix and it’s fine. It will not slip though.   
    • Okay. Final round of testing done. Got a friend to hook up a fancy scanner to the car and we also ran some compression and leakdown tests, she is healthy.  The MAF was definitely the culprit. So for future reference anyone with similar issues that find this thread. I suggest the following steps, in order of affordability:   Check your spark plugs for any fouling, replace plugs if they are bad or re adjust the gaps making it narrower (0.8mm would be good). Check every coil's resistance with a multimeter. It can be done by probing the IB and G pins on the coil pack. Resistance should be around 1.4 (+/- 0.1) Ohms Check the MAF. If you have Nissan connect or a good scanner with the 14 adapter it should allow you to see the voltage on the MAF reading should be around 1.1 - 1.2V when car is idling. But if you don't, buy a new MAF from Amazon and test, then return it. (For instance, I got a Chinese one for $40 that was reporting 1.3v on idle). If you still have scanner, you can run tests on the injectors to see if they are working, just remember to unplug the fuel pump fuse/relay and have no pressure on the line. Then listen for the noises that the injectors make. Clean/replace injectors as needed. Once you find the issue and fix, order thousands of dollars worth of OEM parts to refresh unrelated things (Optional)   PS: Thanks to the absolute legends of this forum for the responses and help to someone that went a bit over their head. (me)
×
×
  • Create New...