Jump to content
SAU Community

Recommended Posts

Found this. Looks like that signal is the opposite of what we want. Bummer 'cause that would have made it pretty easy.

post-76144-0-04244800-1367829961_thumb.jpg

Edited by Commsman

How old was that post Craig? You gotta get out more...

I gave up on the anti lag, it didn't help much as the stally has been returned to a stock stator, and there is no possibility of it ever making boost. Yours would be a different story. I had plans to test another method to pre spool the turbo, compressed air, but this isn't the car to test that theory on. lol.

I can see mine going rwd manual very soon anyway which gets right around the launch issue. Or perhaps I will drop back to a highflow again for launch boosts, and so the gearbox isn't having quite so hard a time.

Anyway, back on topic, the neutral signal will work one way or another, but if it's 12v then it will be a simple strip and twist, nice and easy for a DIY with pics. I will take some shots when I test this out on the next car. (Damn Leon, you beat me to it. Looks like we will need a relay.)

Anyway, back on topic, the neutral signal will work one way or another, but if it's 12v then it will be a simple strip and twist, nice and easy for a DIY with pics. I will take some shots when I test this out on the next car. (Damn Leon, you beat me to it. Looks like we will need a relay.)

Relay will probably work as 0V is normally an earth, but sometimes it is just 0V.

But all is not lost for a dead simple solution. Why not use the Start signal on Pin 42? According to my research, that wire has 9-12V when key in start position & 0V otherwise. Sounds perfect, yes?

post-76144-0-01263000-1367841813_thumb.jpg

DIY instructions:

1) Cut wire on Pin55 a few inches from the ECU connector. Strip ECU end & tape up other end.

2) Strip small amount of insulation from wire on Pin42 (leaving wire intact).

3) Solder Pin55 wire (ECU side) onto Pin42 wire & tape up.

Job done :thumbsup:

post-76144-0-87883200-1367842764_thumb.jpg

Testing & pics are all yours Scotty. I'm not moving mine from where it is as works just fine, but the above is certainly an easier solution....if it performs as expected.

  • 3 weeks later...

so has this been tried and tested yet??

Relay will probably work as 0V is normally an earth, but sometimes it is just 0V.

But all is not lost for a dead simple solution. Why not use the Start signal on Pin 42? According to my research, that wire has 9-12V when key in start position & 0V otherwise. Sounds perfect, yes?

attachicon.gifStart sig on Pin42.JPG

DIY instructions:

1) Cut wire on Pin55 a few inches from the ECU connector. Strip ECU end & tape up other end.

2) Strip small amount of insulation from wire on Pin42 (leaving wire intact).

3) Solder Pin55 wire (ECU side) onto Pin42 wire & tape up.

Job done :thumbsup:

attachicon.gifSimple brake wire mod.JPG

Testing & pics are all yours Scotty. I'm not moving mine from where it is as works just fine, but the above is certainly an easier solution....if it performs as expected.

  • Like 1

would i need to install a diod if i went this option

If you don't want to install a 'valet' switch then you don't need a diode when you connect any 12V source, be it from reverse lights, another pin on the ECU or anywhere else.

Ideally a 12V source close to ECU is best. Just need one that is 12V only at times when you don't need full throttle; eg reversing or starting the car.

The only location for reverse lights that I have found is at the rear, so not very convenient (although I already had a spare wire left over from TV install) & the start signal on the ECU is certainly convenient, but Scotty thinks it may not be active long enough to keep the code clear (although I think it should be OK 'cause when mine put out a CEL it would only take a few seconds with the switch thrown & pedal pushed to clear it).

Why don't you give it a go & let us know? If you do the mod you should know in 500km or so. Cutting one wire & joining it to another seems to be the simplest idea we've come up with so far.

Because it will have looked for the brake wire signal & generally spotted a fault in that time.

Mine sometimes goes weeks without throwing the fault; so it can be a bit hit & miss.

Mine takes about 5 seconds to reset. Still worth trying it, as a quick supply of power might be enough to stop the light from coming on, instead of the few seconds to override the light.

One thing I have noticed is I get better fuel consumption with the light on.

Mine takes about 5 seconds to reset. Still worth trying it, as a quick supply of power might be enough to stop the light from coming on, instead of the few seconds to override the light.

One thing I have noticed is I get better fuel consumption with the light on.

You will.....it will go lean.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...