Jump to content
SAU Community

Recommended Posts

Hey guys, have been searching the forums to no avail for someone who has had similar problems that I am having with my r33 Gtr.

First gear is really hard to engage, same with reverse. And a little notchy throught all of the gears. Mostly like this all the time, I think temperature has a bit to do with it as well as when cold, still notchy and hard to engage but not as bad as when it's hot.

If I roll slowly (-5km/h) it pops into 1st no problems.

Master cylinder is full, visually everything seems to be ok. No leaks that I can see out of the slave cylinder.

Clutch started slipping a tiny bit in 3rd the other morning (gearbox still cool), could this all be tied in?

Really confused and need to get this fixed quickly, its my daily at the moment.

Anyone have any ideas?

Thanks guys.

No clue, I purchased the car a few months ago. Reason I haven't changed it is that I am doing the 100k service next month so I was going to get it all taken care of in 1 hit. This happened all of a sudden though, so I'm guessing it's not that. It was smooth a few days ago and now it's a bitch to drive.

Clutches don't slip if in good condition and nothing wrong, shouldn't matter if its cold or not ( unless its a full carbon, but thats another story ) :closedeyes:

Load it up in 4th and see if it slips again, could answer your question. also change fluid ( make sure you use the right weight oil )

Car is 15+ years old, could just be normal wear on box..

Edited by tricstar

Unless you've had a recent fluid change, gears don't all of a sudden start getting notchy. Therefore unlikely to also be a gearbox oil issue, at least, that doesn't sound like the root of the problem.

The fact it's happening in all gears and happened all of a sudden sounds like it could be clutch related. Specifically, hydraulics...which change with cold/hot temperatures. Get under the car while someone pumps the clutch pedal and check that there is enough travel in your clutch fork. If it's lacking, bleed the system and check for leaks - could have a worn master or slave cylinder.

If there is plenty of travel in the clutch fork, then you may have a worn pressure plate or your spigot bearing is grabbing the input shaft and turning the gearbox even after you press the clutch pedal.

Unless you've had a recent fluid change, gears don't all of a sudden start getting notchy. Therefore unlikely to also be a gearbox oil issue, at least, that doesn't sound like the root of the problem.

The fact it's happening in all gears and happened all of a sudden sounds like it could be clutch related. Specifically, hydraulics...which change with cold/hot temperatures. Get under the car while someone pumps the clutch pedal and check that there is enough travel in your clutch fork. If it's lacking, bleed the system and check for leaks - could have a worn master or slave cylinder.

If there is plenty of travel in the clutch fork, then you may have a worn pressure plate or your spigot bearing is grabbing the input shaft and turning the gearbox even after you press the clutch pedal.

Yea... this is what i thought too. Ill check this out aswell.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...