Jump to content
SAU Community

Recommended Posts

Hey guys, have been searching the forums to no avail for someone who has had similar problems that I am having with my r33 Gtr.

First gear is really hard to engage, same with reverse. And a little notchy throught all of the gears. Mostly like this all the time, I think temperature has a bit to do with it as well as when cold, still notchy and hard to engage but not as bad as when it's hot.

If I roll slowly (-5km/h) it pops into 1st no problems.

Master cylinder is full, visually everything seems to be ok. No leaks that I can see out of the slave cylinder.

Clutch started slipping a tiny bit in 3rd the other morning (gearbox still cool), could this all be tied in?

Really confused and need to get this fixed quickly, its my daily at the moment.

Anyone have any ideas?

Thanks guys.

No clue, I purchased the car a few months ago. Reason I haven't changed it is that I am doing the 100k service next month so I was going to get it all taken care of in 1 hit. This happened all of a sudden though, so I'm guessing it's not that. It was smooth a few days ago and now it's a bitch to drive.

Clutches don't slip if in good condition and nothing wrong, shouldn't matter if its cold or not ( unless its a full carbon, but thats another story ) :closedeyes:

Load it up in 4th and see if it slips again, could answer your question. also change fluid ( make sure you use the right weight oil )

Car is 15+ years old, could just be normal wear on box..

Edited by tricstar

Unless you've had a recent fluid change, gears don't all of a sudden start getting notchy. Therefore unlikely to also be a gearbox oil issue, at least, that doesn't sound like the root of the problem.

The fact it's happening in all gears and happened all of a sudden sounds like it could be clutch related. Specifically, hydraulics...which change with cold/hot temperatures. Get under the car while someone pumps the clutch pedal and check that there is enough travel in your clutch fork. If it's lacking, bleed the system and check for leaks - could have a worn master or slave cylinder.

If there is plenty of travel in the clutch fork, then you may have a worn pressure plate or your spigot bearing is grabbing the input shaft and turning the gearbox even after you press the clutch pedal.

Unless you've had a recent fluid change, gears don't all of a sudden start getting notchy. Therefore unlikely to also be a gearbox oil issue, at least, that doesn't sound like the root of the problem.

The fact it's happening in all gears and happened all of a sudden sounds like it could be clutch related. Specifically, hydraulics...which change with cold/hot temperatures. Get under the car while someone pumps the clutch pedal and check that there is enough travel in your clutch fork. If it's lacking, bleed the system and check for leaks - could have a worn master or slave cylinder.

If there is plenty of travel in the clutch fork, then you may have a worn pressure plate or your spigot bearing is grabbing the input shaft and turning the gearbox even after you press the clutch pedal.

Yea... this is what i thought too. Ill check this out aswell.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...