Jump to content
SAU Community

Recommended Posts

I did not know the S300P was available? Did he elaborate on the wheel/housing sizing on this?

He said it could be made by custom order... Rear housing was a 0.80 T4 divided, wheels I'm not 100% sure but I believe they are similar to the EFR8374 as he mentioned once it was a prototype for that turbo

Now the choice is to get a surge ported from cover or not and where to buy it from...

Surge cover for sure. They are a winner on those turbos. I think the CEA design wheel works well with it.

I will PM you a quote I received for a friend!

  • 6 months later...

This one will be a rear wheel drive GTT with an RB26 in it.

I'm looking for a single turbo/manifold combo that will net around 370kws.

Motor will be kept pretty simple with a built bottom end, drop in poncams, very little headwork, running on E85.

Looking for 20psi by say 4000rpm.

If I were building exactly the same thing, going by the things I've seen out and about these days - I'd go for a single entry FP GT3076R HTA with .82a/r hot side on a 6boost manifold.

I'd say your 370kw on E85, and 20psi by 4000rpm should be pretty achieveable with that combination - potentially with change.

I was trolling around and found this thread - until seeing this I couldn't specifically remember when I had recommended the HTA3076 as I normally have that kind of convo in PM and I'd never found it.... this would be why I didn't remember it, you had asked about a setup for an RB26 :D

Fast forward a year, the project turned into an R33 GTS25t with an RB25 in it but the same power/spool target and you took the plunge on the HTA3076 - looking forward to final results, but do you know if it hit the 20psi by 4000rpm rpm target yet?

Haha i just read this thread again this morning after searching around in circles :P I think the target was met or close too it.

I was pretty confident that the RB26 would do it, and suspect the RB25 should be good for it too - though certainly will be interesting to know how it all comes out. It'll probably never happen to mine now (it was semi-on the cards when this thread started - hence the quick response), so would be good to enjoy vicariously!

I was pretty confident that the RB26 would do it, and suspect the RB25 should be good for it too - though certainly will be interesting to know how it all comes out. It'll probably never happen to mine now (it was semi-on the cards when this thread started - hence the quick response), so would be good to enjoy vicariously!

I think the final tune was to be last week or this week so it should be close too result time! Im keen to see the final numbers too :yes:

Final tune will be late next week now as car is at the painters. Tuner was too busy last week so I took the opportunity to send it to paint in the meantime....

Patience guys, results soon... :yes:

Final tune will be late next week now as car is at the painters. Tuner was too busy last week so I took the opportunity to send it to paint in the meantime....

Patience guys, results soon... :yes:

Late next week is good news to me, I had assumed it was going to be a while before you got back to it :D Would be awesome to see what the overall finished product comes out like when its done :)

Final tune will be late next week now as car is at the painters. Tuner was too busy last week so I took the opportunity to send it to paint in the meantime....

Patience guys, results soon... :yes:

Are you kidding me? :P I am going to fall off my seat with anticipation heheheehe

Really keen to hear, good luck mate :thumbsup:

  • 4 weeks later...

Final tune will be late next week now as car is at the painters. Tuner was too busy last week so I took the opportunity to send it to paint in the meantime....

Patience guys, results soon... :yes:

I've managed to last around 3 weeks without annoying you :D How are things going with this, did it make it to the tuner - or are there still plans to get it back on the dyno sometime soon?

It's on the dyno now actually. Been on a few times this week. Having issues with the ecu losing/not storing tune. Thinks it's fckd. Similar issue to when run in tune was being done.

Damn :( Was really hoping it would go well for you as i was super keen to see the result ;)

Hope the ECU issue gets sorted out and you get the results you are after mate!

Haltech Platinum Pro.

ECU is off to Haltech tomorrow to get checked out.

One day............

Who you speaking too at Haltech?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
×
×
  • Create New...