Jump to content
SAU Community

Recommended Posts

ok due to the head fxxk of the A-LSD, I've decided to change to a mechanical LSD,

so do I just need the standard diff housing? can it be an R32 GTR one ( my car is R33 GTR ), is there any difference? also will the drive shafts and tail shaft bolt staight up to the standard diff?

Get one to suit a 33gtr and everything will bolt up. Go new though as usually you get everything you will need, instead of going 2nd hand and having stuff missing

but from what I have read, I need to change the whole diff housing as there is no after market diff centre to fit into the Active-LSD housing?

I just went through it all. :)

You need to change diff housing to a R33 GTR Non V-Spec. Not expensive, can get them for 200-300 2nd hand.

I thought you needed the non-spec shafts as they are different lengths when you measure.

But it turns out the actual shafts are the same length, it's the coupling big (forget the technical name, bit where the shaft connects with) that is slightly different and I believe it can be purchase separate if you cannot get shafts to suit

Makes it easier/faster if you can get the housing with the shafts together obviously.

The car with a Nismo 1.5 GT Pro is 10000% better than with the crappy A-LSD, which has no upgrade options.

It's set to the lowest lock setting and still locks incredibly hard when you want, very predictable. Any more I think would be too much.

My car now behaves like a RWD car in terms of hooking around @ a motorkhana with a bit of clutch or trailing throttle lock-up and turn - yet straighten the wheels and it 4 wheel power slides nicely or grips and goes depending on what you want.

Also induces some good mid corner oversteer where previously it would just understeer/plough off terribly doing the same things ;)

I didn't realise how bad the A-LSD was until changing over... I don't wanna sell the car now it's changed it that much

I don't know mate - I was told to get a R33 rear end specifically.

I know the part numbers for R32 & R33 are the same in terms of the Nismo differential... Doesn't mean the housings are though...

Someone will be able to confirm though 100%

I just did this in my gtst. I bought a second hand regular gtst diff and just threw it in.... everything fitted up fine for me, the only thing i needed was a new set of nuts and bolts to connect the halfshafts to the axles as the a-lsd halfshafts were threaded and the gtst ones were not....

Ripped out the pump and reservoir as well.

At the time I just shimmed the new diff, but thats shit and only lasted a few weeks and I absolutely locked the fark out of it.... next mod is either a kaaz or nismo centre.

Ye that doesn't surprise me.

Ideally yes you want diff & axles. It just makes it a simple bolt in/out (once you do the centre.)

But... if you can't get the shafts, you can use your v-spec ones as they are the same length. It's just the the coupling bit that's the different length betweeen VS and non-VS (the technical name for the part still escapes me)...

I can find out the proper name and shit next week exactly and report back. I doubt you'll find a R33 non-VS rear in a couple days. I was looking for a good 2 months for one priced appropriately.

spoke to a mate in the know last night and the R32 GTR diff and axles is a touch shorter...

so I'm after a R33 GTR non-Vspec diff and axles, anyone ??

Yes they are, I have measured them as I have a R32 GTR diff. from a 1994 car to replace my A-LSD. Just need some spacers machined, from memory it is only about 5mm.

OK I've got the Non V-spec diff and axles,

now I have a few questions about what to do regarding the hydraulics and electrics?

My thinking is, just block off the hydraulics from the pump under the car and rip everything from there to the diff out.. I'm thinking I shouldn't need to cut or disconnect any wiring (except the obvious between pump and diff) as the new diff will be locked before any signal is sent.? Being that the A-LSD is on the same circuit as the AWD I don't want to hack it and then get faults with the AWD ?

How do others do it ? What have you blocked off, cut etc?? (Nismoid)?

The Transfer case & rear diff pumps are all in the same cradle so easier just to leave them there and remove the lines which is what happened to mine.

I cant remember if the power feed for the A-LSD was disconnected. It's not throwing any failure lights, i know that much. I'll find out and report back next week.

The Transfer case & rear diff pumps are all in the same cradle so easier just to leave them there and remove the lines which is what happened to mine.

I cant remember if the power feed for the A-LSD was disconnected. It's not throwing any failure lights, i know that much. I'll find out and report back next week.

cool, can you also have a look and see if they blocked off the line from reservoir in the boot or just the line from solenoid to diff?I should do a DIY when I do the swap for future reference.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • how do you know voltage is fine?  quick easy test is connect DMM up and put it on max/min mode, remove fuel pump fuse, crank car for 3-5s, go check min voltage You'd be surprised how many "healthy" batteries are showing under 10v during this test in cold weather. 
    • Not properly. You need to be able to dissipate 100 amps or so to doing it meaningfully. You can do it indirectly by watching to see how far the voltage falls during cranking. Unplug the coils or something else to prevent it from starting so you can get a good couple or three chugs. It also helps if you have the multimeter set up reading before you start, and that it has max/min functions. So you can catch the real minimum without having to watch the screen, which often doesn't update fast enough to show the real max/min in dynamic situations. Or use a digital oscilloscope, which can be obtained for <<$100 from Aliexpress (although I'd argue for paying up to ~$200 for a nicer one). A >4 yr old battery will very likely be well down the path to the knackery. Many only last 5-6 years these days. The cold weather lately will definitely make it worse.
    • Hmmm, what do you mean by getting weaker? And where did you get that test done? I've been wondering about my battery because the cold starts crank super slowly. The voltage is fine. Not sure if cranking amps can be checked at home. Battery is 4+ years old.
    • No. The simplest wastegate hookup, with no solenoid or other form of "boost control" (ie, control over your boost control, if you know what I mean) is a single hose, direct from the turbo outlet/hot pipe, straight and only to the wastegate actuator. It is that pressure signal that drives the wastegate to open, providing the boost control (and by "boost control" here, I mean, limiting how high it can go, which is essentially the spring pressure of the actuator). You only end up with tee pieces and alternate flow paths once you start adding things to the boost control system to allow you to determine how much of that boost signal makes it to the actuator. There are so many ways to do that that there is no single way to run the hoses and tees and the like. If you have a stock boost solenoid, then all it does is either allow all the boost signal to go to the actuator, or open up to allow some of it to bleed off. There needs to be a restriction in that bleeder to allow only a small amount to bleed off. And in a stock system, that would then be plumbed back to the turbo inlet (for "emissions control" reasons). That is actually what that nipple on your BOV return pipe could/would be for. If you have an aftermarket boost controller and solenoid, then the above is mostly true, but there is no need for a restrictor in the bleed, because the solenoid is pulse width modulated to create a variable bleed off. The air that escapes from the bleed can either be vented, or also returned to the turbo inlet. For emissions reasons it should be returned to inlet, but the amount of air being vented is so small that it really doesn't matter (either from an emissions perspective, or from an air-fuel ratio affecting perspective).
    • And other times you just need to go buy bigger injectors?
×
×
  • Create New...