Jump to content
SAU Community

Recommended Posts

Microtech LT12s has an AUX output, you need to set up a relay thats triggered from the output, the AUX can be set with RPM on and off. Should see a decent midrange gain from the VCT, it will have to be retuned.

Edited by 51NNA

Nothing wrong with microtech's, i've had 3 car that run them! They never gave me any problems an did everything i needed it to do, no point in buying a ecu with all the bells and whistles if u never use them!

fark it annoys me when ppl post garabage like this about computers... Im sure it will do more then enough for what most ppl neeed.... I never had a problem...

Doesn't mean it is a good idea to run it !

I bet I could set up a carby blow through set up on my rb25 and it would be "good enough" and if it worked I could say "without a problem" as well.

The stock ECU has better tunability than a microtech, it has more features and does an all round better job at every single part of running a car.

You have paid money for a down grade.

Nothing wrong with microtech's, i've had 3 car that run them! They never gave me any problems an did everything i needed it to do, no point in buying a ecu with all the bells and whistles if u never use them!

You are right I don't ever use my nice cold start, my idle air valve control that automatically adjusts when the AC comes on, I also don't need fuel economy via an O2 sensor.

Actually Rolls, fuel economy is one place where it is so much easier with a Microtech than with Nistune. It's really hard to lean out the cruise section in Nistune. It's a doddle with a Microtech.

You cannot argue against the statement that a Microtech actually does a decent job of running a fairly simple engine like an RB. Sure, you miss out on a few things, but they do work, and are fairly easy to tune (once you're used to their arse backwards electronic carby way of doing things). I'd much rather have a Microtech than pretty much any Haltech that's ever been released.

Yeah I know they work, but the lack a lot of the handy factory features that the factory ECU has. You can lean out cruise on a nistune the same way if you want, just turn off O2 feedback and pull fuel out until you are happy, or if you are lazy just leave the O2 feedback on and it'll be about the same as the factory fuel economy if you don't stuff things up too much.

  • 1 year later...

quote by rolls, "I like to construct strong views on random things, and then argue for absolutely no reason about them." some one needs a hug? anyone in Adelaide can help out?

before you flame me rolls, i agree with you about functionality of the nistune, however they carry an awsome reputation for results built from racing results! They are designed for high reving rotary's with fast and reliable processing time.

  • Like 1

quote by rolls, "I like to construct strong views on random things, and then argue for absolutely no reason about them." some one needs a hug? anyone in Adelaide can help out?

before you flame me rolls, i agree with you about functionality of the nistune, however they carry an awsome reputation for results built from racing results! They are designed for high reving rotary's with fast and reliable processing time.

Awesome rep from back in the day when they were a great ECU, it is like getting a magazine from the 90s where windows 95 and a pentium 200 was amazing, doesn't mean it still stands up that well today, sure if all you want to do is run excel from the nineties it probably does it well (eg running a rotary that used to be carby fed), but once again doesn't mean it is great today.

There "fast and reliable processing time" is slower and no less reliable than any new ECU.

Edited by Rolls

They are an absolute bucket of shit. Customer support is pathetic, you can't do a thing with them unless handing over wads of cash and the software sucks balls. We had to send a rb25 one back to get something as simple as a thermo fan output enabled, which is yet something else they charge you for.

The vct can be turned on and off in the aux screen.

Actually Rolls, fuel economy is one place where it is so much easier with a Microtech than with Nistune. It's really hard to lean out the cruise section in Nistune. It's a doddle with a Microtech.

what? just highlight the cells you want and press 'O' then drop the value to whatever you want.. it's dead beat simple... I've used Microtech before, it's so damn confusing.

1x table for RPM vs. Timing, then 1x table for Timing trim vs. Load... no sure why they just didn't want to use a 3D map like other people.

what? just highlight the cells you want and press 'O' then drop the value to whatever you want.. it's dead beat simple... I've used Microtech before, it's so damn confusing.

1x table for RPM vs. Timing, then 1x table for Timing trim vs. Load... no sure why they just didn't want to use a 3D map like other people.

Yup. Unless you wanted to keep closed loop. And perhaps you've not tried to do it on a more modern Nissan ECU? VE tables make it hard to know if you're achieving anything at all. You can't switch off feedback on a per cell basis on those anyway.

I'm not defending Microtech by the way. They are unpleasant to tune, as I stated in my original post. But especially back when the only Nissans being played with were RB20s and CA18s, they did a good job, and did return excellent fuel economy - far better than stock.

Yup. Unless you wanted to keep closed loop. And perhaps you've not tried to do it on a more modern Nissan ECU? VE tables make it hard to know if you're achieving anything at all. You can't switch off feedback on a per cell basis on those anyway.

I'm not defending Microtech by the way. They are unpleasant to tune, as I stated in my original post. But especially back when the only Nissans being played with were RB20s and CA18s, they did a good job, and did return excellent fuel economy - far better than stock.

I do find that the Nistune O2 closed loop is funny, it's quite lazy. I prefer to just set at stoich of the bat for idle/cruise etc. and I turn it off as it comes on song. It tries to stoich coming onto boost which makes the car feel lazy. I've only ever used it on a R33 and S15s nothing newer so perhaps you're right.

Do many people tune nistunes with the O2 feedback off?

you always need to disable O2 feedback whilst tuning, then re-enable it once you're done.. however I just leave it off completely on the idle/cruise cells.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...