Jump to content
SAU Community

Recommended Posts

Genuine Nissan item, works great - I love how it stops stuff sliding around the back of the Stagea. Only selling because we're getting a Cube for day to day driving/shopping - my Stagea is just a bike mover now.

$400 ono.

Big photo of the net itself is the one for sale, the other photo shows the possible configurations, but is from a Nissan catalogue.

post-18615-0-63991600-1337073200_thumb.jpg

post-18615-0-39663200-1337073202_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/400189-m35-stagea-cargo-net/
Share on other sites

  • 2 weeks later...

Did a search but couldn't find jack..I ordered this with a few other things from Japan but the absolute minimum it could have cost me is about $380, but likely set me back over the $400 mark since it was the heaviest item in the order.

Like I said, open to offers, but with the exchange rate the way it is I dunno how you could find one of these for $250 anyway. I'm just trying to recoup what I spent.

Fair enough but I always work on the idea that once I have bought it its second hand and can't expect to get back what I paid. Plus I worked on the fact that no one locally would have paid ~$400 for it despite the fact it might have cost you that via Japan.

http://www.skylinesaustralia.com/forums/topic/378072-m35-cargo-barrier-safety-net/page__pid__6030459#entry6030459

Edited by slippylotion

Yours, and mine were second hand before either of us bought them.

As far as I'm concerned, if you buy something second hand, barely use it and the condition doesn't change, neither does the price.

That said, when did you become a moderator anyway?

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Your other option is to buy a spray can of hi-fill and prime it with some pinholes. See if the primer makes them disappear. If it does, then you can leave it with pinholes of that size and they will go away when the painter takes over.
    • Ah ok. I seem to be mixing it like everyone else does so not sure what's happening. Will experiment with it more.
    • Depends on what you mean by OK. First up, was this done cold or hot? Are they reasonably consistent? Yes, they are reasonably consistent. Could be better. But unless it has had a build at some point, it is a ~30 year old engine and you'd expect some variation. Some of the difference could also be in user technique Is it good compression? Well....not numerically, no. New they were >160 psi. The one at 140 would be fine, in that context. If they were all ~140, you'd be reasonably happy. But the one that is @120 is twice as far down from the original numbers as the one @ 140. But.. (again)... technique can play a part in the absolute magnitude of these numbers, and the quality/state of repair/accuracy of the pressure gauge is not known. In the context of the above, the compression tester that was used last on my car is regularly compared to a known good pressure gauge. Not calibrated, exactly, but compared to a reference instrument that is not used for any other purpose, so cops no abuse. So we can trust the measurements off that tester. But another tester in the same workshop wasn't being compared against the standard and was reading a good 30ish psi lower. When you're reading 100 psu but the engine is really doing 130, you can make bad decisions.
    • More likely from tiny bubbles in the filler/putty. Maybe be less aggressive when mixing it. Perhaps invest in a vacuum chamber to pull the air bubbles out?** **I don't know if this is a thing for body filler. I see hardcore epoxy makers degassing their mixed resin on the regular.
    • IIRC, the speedo on these is fed from the sensor in/on the snout of the diff.
×
×
  • Create New...