Jump to content
SAU Community

Recommended Posts

Sorry to Hi-jack your thread but does anyone know with "street semi's" like Federal RSR's for example is there any point in warming them up at the drags or are they the same as normal street tyres that don't like heat?

Sorry to Hi-jack your thread but does anyone know with "street semi's" like Federal RSR's for example is there any point in warming them up at the drags or are they the same as normal street tyres that don't like heat?

its always good to warm up the tyres this will give you bit of extra grip , you probably seen other cars running semi or even full slick still warming them up.

its always good to warm up the tyres this will give you bit of extra grip , you probably seen other cars running semi or even full slick still warming them up.

I under stand the guys with race tyres warming them up coz race tyres only work at a certain operating temp's but street tyres are designed not to need to be warmed up to be able to produce grip & iv been told heating them can actually make things worst. So just wondering how these street semi's work.

It comes down to how much power your car is putting down and how serious you are.

Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car?

If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race).

So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

I under stand the guys with race tyres warming them up coz race tyres only work at a certain operating temp's but street tyres are designed not to need to be warmed up to be able to produce grip & iv been told heating them can actually make things worst. So just wondering how these street semi's work.

pretty sure the tyres will be warming up regardless, when doing a burn out you give the tyre the chance to grip the surface properly when taking off i own MT semi slick tyres and yes they are meant to be warmed up , those that dont properly dont have the option to, however from experience , it works.

Edited by Hiroshima Screamer

It comes down to how much power your car is putting down and how serious you are.

Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car?

If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race).

So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

you haven't been to the drags much have you? i was having traction issues with about 180hp (so about 135kw) in my magna. a mate of mine had a sr20 in a sigma and with street slicks he was lifting one of the front wheels off the ground when launching and he only had about 250hp. he was simply holding it on the rev limiter and pretty much just side stepping the clutch. his 60' times were around 1.5 seconds.

you haven't been to the drags much have you? i was having traction issues with about 180hp (so about 135kw) in my magna. a mate of mine had a sr20 in a sigma and with street slicks he was lifting one of the front wheels off the ground when launching and he only had about 250hp. he was simply holding it on the rev limiter and pretty much just side stepping the clutch. his 60' times were around 1.5 seconds.

Actually, I have.

My 33 was a typical 11psi, FMIC, exhaust and pretty healthy. I had china specials on the back and traction was never an issue. I could light up the rears in first and a tiny chip/squirm into second if I wanted, but by christ I had to be pumping it pretty friggin' hard. Pull back to 95%, which is sensible if it's your daily, and traction was not an issue.

It comes down to how much power your car is putting down and how serious you are. Do you have a 185kw, FMIC, exhaust, filter car or a 300kw, GT3076 + supporting mods car or a 350+, forged, gt35 + all the fruit car? If it's 185, a warm up is pointless, traction won't be an issue. If it's ~300ish then it might be of use you're running street tyres, but in reality you'll do better simply managing your throttle and clutch better. If it's the last option, then I would expect you are running slicks and intend on launching hard and a warm up burn out is definitely beneficial (if not slicks then no amount of street tyre burnout is going to stop you wheel spinning for a good portion of the race). So, in conclusion, I'm going to bet your running moderate power on street tyres which means a pre race burnout is going to give very limited benefit. But do one anyway, cause they are fun :)

I dono my R34 was only making 165rwkw & i was having some pretty big traction issue. Had to baby it off the line (holding it at about 3 grand, slowly stepping off the clutch & waiting before I went to WOT) otherwise I went no where just spun.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...