Jump to content
SAU Community

Eoi:- Private Drag Day At Adelaide 1/4 Mile. July 1St 2012


Recommended Posts

  • Replies 197
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Jap_Star the WR600 indicates a final power output figure of 600kw or 800hp crankshaft power potential from the package. Currently it makes 460kw or 620hp at all four wheels on track rubber, so we are getting close :)

hey mardy wanna see some of the 35 u going to be there all day sunday weather permitting?

and that 60 needs some love :whistling: . one of the boys did a 1.47 60ft with a non stalled zf no gears either 2wd lol :wub:

A decent wire to the alternator might be worth a try then matt, only cost a few bucks. what turbo you using atm?

What powers the r35 gtr make to run in the low 10s?

Andrew

I'll certainly look at it as an option mate, makes perfect sense.

Current turbo is a custom Turbonetics T62-1, had it for a few years now. It will produce approximately 625-650HP.

I'll certainly look at it as an option mate, makes perfect sense.

Current turbo is a custom Turbonetics T62-1, had it for a few years now. It will produce approximately 625-650HP.

Nice matt, Are you running tomorow?

Is the day still going ahead? chance of rain i heard.

Fingers crossed the rain holds off or doesn't pass through the area. I'm planning on running, weather is the main deciding factor. Please, please don't rain! I've been waiting 6 years for this!!!

so i got some vids of a white r32,burgandy33 and a black 33 and munro and willal's 35 ( what happened marty ) if u want ill post some up if u dont want also say and i wont up load them to u tube

Have updated my signature!

Is it possible to edit out the rego plates if going on youtube?

One run I did a prelaunch & put it into limp mode. Held it flat but

would only let me do a 19 sec pass - man it felt like forever!

The other 4 runs we good though, pretty happy with that.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...