Jump to content
SAU Community

Recommended Posts

  • Replies 53
  • Created
  • Last Reply

Top Posters In This Topic

seats SOLD

seat belts SOLD

diff and half shafts SOLD

door trims SOLD

Carpet SOLD

WAITING ON 'TYPEVU' TO GET BACK TO ME ABOUT THE SHELL ASAP!!!!! 0417080960

silver series 2 wing $40

hicas ECU $40

steering rack $70

Front brakes $300

rear brakes/lca's/handbrake cables $450

WED racing 2 piece wheels with great tyres $450

Tanabe cat back exhuast $220

stainless split dump $40

Stock turbo/mani $200

door locks/ignition still on column with key $100

passenger window reg/rail $60

drivers n pass central locking motors $40 each

Digital climate unit $40

stock seat belts $40

stock front castor rear/camber toe arms $50 the lot

heaps of crap here come get some :P

glovebox SOLD

centre dash vents SOLD

gearboot/surround SOLD

shell back up for sale due to no contact.....

slight/meduim front hit, be ok for tracker currently rolling with full rear brake set up, all stock suspension, hicas, straight doors, all glass fuel tank, boot, tail lights, bumper,$800

$400 no rear hub/brakes etc need it gone ASAP!!! may swap for aftermarket rb25 parts

ignition/door/boot locks and key $100

i am currently looking for fixed back seats/harness's hydro handbrake/ gauges/ etc etc

i have a cabinet full of r33 bits if something isnt listed please dont hesitate to ask!!!

Tail lights SOLD

headlight/indicator stalk SOLD

pass window switch SOLD

heater box SOLD

Handbrake mount/handle etc ON HOLD

Stainless top mount manifold heat wrapped $220

series 2 wing silver $40

abs unit $40

hicas ecu $40

power steer rack $60

pass window reg n rail $50

heaps of bits still here just ask

NEED SHELL GONE!!!!!

It comes with straight doors, straight rear quaters, all suspension arms and sway bars, that includes front lca's and 5 stud hubs (no struts/springs) full body loom, all windows they haven't been taken out, rear cradle with hicas, fuel tank.

Can negotiate other bits I have taken off to go with it.

Will take trade for parts, wheels/harness's/adj sus arms etc

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Dear folks My family members have 4 different cars : Triton 2015 and Corolla 2011 and Mazda3 2012 and Hyundai Elantra 2014 Looking to buy engine oil funnel spill free What I found are are below  https://www.amazon.com/gp/aw/d/B0BBTTJNKX?ref=ppx_pt2_mob_b_prod_image&th=1 https://www.ebay.com.au/itm/145553221359?srsltid=AfmBOoqYBU6Ptw0LU_bAp_k67U3qkF97HHvePkA7iHZw8vUmiwoIRaRr https://www.amazon.com/gp/product/B09X23TCS5?th=1 Is there a funnel with attachment that fits most cars ? Don't mind to spend for a decent quality  Thx  
    • Stock ECU (or more accurately stock tune) absolutely refuses to go over 10psi and behaves like you have seen. The Nistune is the same if it is the stock tune. If the Nistune chip has been tuned, the resulting tune could be literally anything for any combination of parts. The Nistune just makes the stock ECU Tunable.
    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
×
×
  • Create New...