Jump to content
SAU Community

Short Shifter Advice

suwidji
 Share

Recommended Posts

suwidji Experienced

suwidji

Posted
Posted

I'm looking at getting a short shifter, but I can't seem to find a place to get them in Sydney (I'm probably not looking hard enough, but I've done my fair share of google searching lol)

Anyone know where I can get one for my r34 GT-T? I heard the japspeed short shifter kit was good, lots of guides on how to install it too- any others and where to buy them? I have no idea where to get the japspeed one though, because everytime I search it up, it always takes me to a UK site.

thanks!

Link to comment
https://www.sau.com.au/forums/topic/403261-short-shifter-advice/
Share on other sites
suwidji Experienced

suwidji

Posted
  • Author
Posted

ha, it's in the throw not the lever length

yeh that's what i was thinking. a short shifter usually has the same length as the original shifter right? The difference is the pivot point which reduces the throw.

Anyways, anybody know where I can get one?

89CAL Grand Master

89CAL

Posted
Posted

eBay, just jap. Lots of places. I had a spare so I made my own. Just cut the threaded part off, got rid of the rubber filled top section and welded the threaded part to the inner section of the shifter. I wanted a solid shifter with a bit less length so pretty happy with it

89CAL Grand Master

89CAL

Posted
Posted

short shifter has the same length lever but needs to be moved a shorter distance to select gears

Yeah pretty much this. I've seen the eBay ones and they basically raise the pivot point so less throw is needed

The way I described above doesn't decrease the throw just decreases the length of the shifter. Gives the illusion of a shorter throw basically

StevenCJR31 Veteran

StevenCJR31

Posted
Posted

Yeah pretty much this. I've seen the eBay ones and they basically raise the pivot point so less throw is needed

The way I described above doesn't decrease the throw just decreases the length of the shifter. Gives the illusion of a shorter throw basically

so a shortened factory shifter would serve the same purpose (?) as the pivot point would be difficult (at best) to change?

  • 5 years later...
Hasitha Rookie

Hasitha

Posted
Posted

In layman's term. The gear/shifter handle lenght is relatively the same as stock, but the movement required to change a gear is less than a stock. Cutting the lever doesn' t mean its a short shift it just its a short lever same shift.
I mighy be wrong in the following but I belive the 34 Gtr comes with one and the Tomei Chaser too comes with a short shift.

  • 2 weeks later...
  • 1 year later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      Lamb roast on Saturday will be different 🥲
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • GTSBoy
      RB25DET with solid lifters - which cams ?

      By GTSBoy · Posted

      I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • TurboTapin
      RB25DET with solid lifters - which cams ?

      By TurboTapin · Posted

      I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...