Jump to content
SAU Community

Recommended Posts

6 speed conversion buddy. Should have done it last time the box melted. Its a shame loosing the AWD but the weight saving alone will make it all worth while I think.

I'm so over the auto, why won't it just shift when I tell it to...

I'm so over the auto, why won't it just shift when I tell it to...

A= BFS - numbers in map are too low. Low numbers = slow shifts; but don't know how you'd go about changing that since your injectors are controlled by F-con, correct?.

6 speed sounds like the best solution for you though.

Shifts are fast but the time it takes to decide is a joke. Usually it just bounces off the 7500 limiter on wot, not good at this power. Plus the gearbox won't drop in to a lower gear until the shaft speed has slowed enough, it's horrible changing gears in corners...

Added to the usual crappy reaction times, the box can only do 2 laps of PI without overheating, and causing weird transmission faults.

Not much point if it cant hold the power, even if I could fit the PM35 box. I'm not going down the 33/34 GTR box either, a whole can of worms.

As the easiest, most logical and cheapest option I decided on the 350Z box. At least I can swap back if I ever need to... But I will be leaving the console handbrake. ;)

Rather than clutter this Attessa thread I will start another to discuss it.

  • 4 weeks later...

so i took my baby to kewish (thanks scott). Error came up as 4WD Actuator Relay C1205.

Sounds relatively inexpensive :) (i hope).

Anyone done one of these? Advise on where it is and part number would be appreciated.

Thanks gents.

Go to page 20 in the attachment, in the picture marked A the smaller item on the left labeled "E-TS アクチュエーターリレ" is the E-TS actuator relay. It's basically just beside the 4wd ecu, below the attesa fluid reservoir which is all in the boot wall behind the storage thingo on the drivers side.

I :wub: Google translate.

TF - Transfer.pdf

Hmm not really clear, if you look in the attachment for pressure switch

圧力SW

or

圧力スイッチ

There are a few references but it's more about testing the functionality rather than where it is located. Try and find out the code and that will probably help otherwise if you have a multimeter and know what you are doing there are a few voltage and continuity tests you could do, let me know if you need more help.

There is also this thread http://www.skylinesaustralia.com/forums/topic/402973-m35-attesa-ets-pressure-switch-problems/

What symptoms are you having?

Hmm not really clear, if you look in the attachment for pressure switch

圧力SW

or

圧力スイッチ

There are a few references but it's more about testing the functionality rather than where it is located. Try and find out the code and that will probably help otherwise if you have a multimeter and know what you are doing there are a few voltage and continuity tests you could do, let me know if you need more help.

There is also this thread http://www.skylinesa...witch-problems/

What symptoms are you having?

My prob sounds very similar to that post except i'm not getting the pump chirping. Also when my light comes on i loose 4wd all together(which is fun in the wet haha) i would say 90% of the time its ok, and seems very spiratic when it fails, just seems to fail at any random time.

You could try getting your battery tested I know that these cars seem to start acting strange when the battery starts to go. Otherwise I would try the multimeter tests mentioned in the service manual.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...