Jump to content
SAU Community

Recommended Posts

Hi,

Just bought a R33 GTSt, I am upgrading the intercooler and piping and need to know what size bloe of valve adapter i need

on the piping.

What is the best BOV for a 33 gtst, 25mm, 32mm or 38mm?

This is the kit for the cooler and piping.

https://www.plazmaman.com/shop_itemdetail.php?itemid=142&cate=35

Cheers

Edited by slamaa
Link to comment
https://www.sau.com.au/forums/topic/403888-bov-size/
Share on other sites

This is the advice :)

Or use a single GTR BOV

either/or is fine.

+1. I used to run a GTR BOV when I first got my gts-t.

I now run a Turbosmart dual port plumbed back... Apparently good for 40psi.. Which is good because I'm looking at running quite a bit out of a EFR eventually.

When they get sorted, anyway >.<

Link to comment
https://www.sau.com.au/forums/topic/403888-bov-size/#findComment-6426462
Share on other sites

just leave the stock one on there..... there is no reason to change it

Looks like my FFP piping kit, it was cheaper and easier to weld the adapter than it was to source the flange for the stock on, and my stock one leaked... So there is occasionally a reason to change them :P

Mr no BOV man!!

Link to comment
https://www.sau.com.au/forums/topic/403888-bov-size/#findComment-6426790
Share on other sites

or run none and have this:

(I have to stop reposting this LOL)

gallery_8001_314_55885.jpg

Serious note, doesn't really matter if you're not smashing much boost down the motor, most if not all guys make about 300 or so use the stock one or nothing.

Link to comment
https://www.sau.com.au/forums/topic/403888-bov-size/#findComment-6427564
Share on other sites

Cool, thanks for the help, another quick question, would a straight 3" pipe from the dump loose too much pressure? or will i need to add in a muffler etc keeping in mind its for track use and will not be registered

It's track, straight through, side pipe..... Go nuts!!

Link to comment
https://www.sau.com.au/forums/topic/403888-bov-size/#findComment-6427964
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
    • I've managed to find this: Nissan_Stagea_AutechVersion260RS (1).pdf
×
×
  • Create New...