Jump to content
SAU Community

Rb25 In R32 Not The Usual Problems

HR32GTS 4DOOR
 Share

Recommended Posts

DVS JEZ Grand Master

DVS JEZ

Posted
Posted

Yeah had it running off the actuator and made 5 psi fine and spiked to 7 sometimes which i dont really care too much about, but it still felt slow. like it still makes boost and you can hear the turbo spooling but doesn't do much with it.

Its a stock skyline. U might be expecting too much :)

Get it on a dyno then u will know if it is making the correct power.

HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
  • Author
Posted

Its a stock skyline. U might be expecting too much :)

Get it on a dyno then u will know if it is making the correct power.

Yeah that is what i was kind of starting to think, but it feels slower than my mates old stockish 32 with an rb20det not a 25. its definitely not slow up top is just majorly lacking in midrange torque

HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
  • Author
Posted

Nah wasn't just going up windy point rd or whatever its called in 3rd.

Ok so took the exhaust off and went for a drive. No difference just made more boost (running off gate spring). still sluggish between 3-5000

HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
  • Author
Posted

Should probably post more about the drive with no exhaust. when boost builds the car just gets very loud and droney but once it is past the flat spot it sounds quite normal like it should. can't tell change in sound with exhaust on since quiet exhaust. So probably the timing is just hella retarded I'll hook up a timing light when I get the chance.

  • 5 weeks later...
HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
  • Author
Posted

been a while since I posted here but I finally hooked up a timing light, set it at 15 deg, drove it, made it worse so assumed it was reading double, then tried to do it again but now it wont idle properly, like it will jump between 600-1000 rpm so i can't get a good reading for the timing. turning the screw on the AAC valve does nothing. also if i take the filter off the AFM (AFM still on car tho) it gets a lot worse, like idle drops and eventually stalls. also I connected up the VCT and that did nothing.

  • 1 month later...
HR32GTS 4DOOR Community Regular

HR32GTS 4DOOR

Posted
  • Author
Posted

Ok so after doing a bit of research I found that I may not have the standard rb25det injectors.

Am I correct to believe that the standard RB25DET injectors are purple?

The plenum on the engine does not have the little nipple on the back of the plenum for the stock boost gage so I believe it may be from a non turbo rb25. (the plenum came off a different engine to the one it is on now)

The injectors on the engine now are red, As said before, am using rb25det computer so I doubt the car would run if non turbo rb25 injectors were used.

Help would be great guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Duncan's V37.......race car?

      By MBS206 · Posted

      Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • Duncan
      Duncan's V37.......race car?

      By Duncan · Posted

      So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • RP1421
      S15 Spec R

      By RP1421 · Posted

      As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • joshuaho96
      R32 GTS (RB20DE) Injectors Replacement

      By joshuaho96 · Posted

      I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...