Jump to content
SAU Community

Recommended Posts

Hello,

Purchased some Nismo 740 (supposedly)

Installed in the car and it runs pig rich. Good sign that these are larger than standard RB25 injectors.

However, the Nismos i have, only have a single hole.

From what I gather they are suppose to have a 4 hole spray pattern.

Something odd here?

Link to comment
https://www.sau.com.au/forums/topic/404882-bought-some-nismo-740/
Share on other sites

Nismo 740 (4 holes): http://www.rhdjapan.com/nismo-high-flow-volume-injector-side-feed-740cc-10136

If they are indeed 1 hole, then you most likely have highflowed injectors, RX7 injectors (480cc) or SR injectors (270cc?). Both have red tops.

Hmm, doesnt sound good.

Car is hopefully going in for a tune soon, so we'll see what happens.

Car is running like a bastard, so its definitely larger in injectors. The mountain of black smoke on idle is an indicator.

I had rx7 550cc injectors in my Corolla, so im familiar with the sort and its not them, besides they are a square plug.

Alright here are the injectors.

They say a46-00 on them, the otherside is hard to mark out, looks like 0f69936

Cant make what of the injectors. The car runs rich as f**k, barely idles, billows black smoke out the back.

Might have to get them flow tested.

6QIsP.jpg

DxC2u.jpg

Edited by privatealpha

The money is on them being SR S15 480cc injectors, minus the pintle caps (where the heck are they!!!?). Also looks like where the injector should be silver, has been painted black.

Here's what they look like: http://1.bp.blogspot.com/_7y7I_iLm7Y0/S9aVoMAwDvI/AAAAAAAAAWk/UhJ6MCUuzY8/s1600/USED+S15+INJECTOR+480CC+NEAR+NEW.jpg

You might not even have highflowed injectors even, just regular 480cc's.

Well i took injectors 1 and 6 to the fuel shop.

They were the easiest ones to remove quickly whilst the rail still being attached.

Results, injector 1 flows at 758cc per minute and injector 6 at 754cc per minute.

So at this stage, Im just going to assume the other 4 are with in those margins.

No idea what injectors they are but they flow exactly how it was advertised, a little more even.

I guess if they aren't nismo's they are high flows? Possibly a high flowed S15 one?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Power steering is probably because someone has nuked the HICAS CU and you no longer have the variable power asist doing what it is supposed to. How much boost are you running? You are aware that any more than 10 psi on the stock ECU is just asking for it to go to full R&R (that's Rich & Retard, which is effectively Retarded and Retarded!) which kills all the power. Depending on the exact conditions, it can just be runnign on the fat and stupid end of the maps, then the conditions change, you make a little more boost and the ECU goes into panic.
    • @BuiltNotBought Just as GTSboy said.   If you want driveabilty and more low down torque..keep the stock runners. They are VERY good from a factory. I have them too on my RB25DET NEO and as a GTSboy i have fmic but with stock piping route(i have Blitz intercooler) Iam making around 320 BHP and the car pulls "hard" from like 2,5k all the way to 7k. I have it dyno tuned to mimic N/A power curve and making little less max torque due to the smallbox tranny. But driveability is very great. I had 350Nm below 3k so car feels very quick.   EDIT:  Not my channel but i saw this and i know that is what i want (and i have exactly this)  
    • Looking to sort out a couple of issues on my skyline  It recently was rebuilt, however rebuilder long story short did not give two flying effs about the work he did. So moving forward it's running but I have two persistent issues 1) it has a misfire / lag type of issue (was at higher RPMs but I had a dead piggy back ecu removed which improved it) now it's not as bad but still does it at random, I thought it may have been a boost issue I'm running an older turbosmart dual stage controller, turbosmart told me to try running off gate pressure however it still has a lag at random times. It has New MAF, maf plug, coil packs, sparks, CP harness.. injectors tested and cleaned. Factory ECU. 2) Power steering issue. It is tight as anything. Flushed power steering, rebuilt my pump because the bearing was shot. Flushed again still tight (mainly when parking and going slow into my driveway etc)  No kinks in hard lines, replaced the lines I could see had cracks. Still tough to steer.  I was told to shim a coin and place into the solenoid plug? Is there anything else. My steering angle sensor also has a issue. It's a used one I replaced, does it need to be calibrated? I feel like I've tried everything and this car is my voodoo doll.   
    • Holy shit... wow!!! I totally missed this
    • One main filter. Each tank has a prefilter to keep rocks and small children out, then the big main filter that also does water separation. Clogged the first one so bad it was like a rev limiter at 3200rpm. Literally just like dropping the throttle off and maintaining rpm!
×
×
  • Create New...