Jump to content
SAU Community

Noise From Cam Cover

R33ram

By R33ram,
in General Maintenance

 Share

Recommended Posts

R33ram Enthusiast

R33ram

Posted
Posted (edited)

hey guys just a quick question...

have this noise coming from my cam cover.

when its cold sounds a lil loud with revs around 1200/1300 rpm.

when i rev it goes away after 1600rpm and when idling at around 900/1000 can just hear it a little bit.

as it warms up it goes away at normal temp and goes away...

heres a video of it similar to mine or almost identical to be honest at the last 25 secs of video.

100% from the cam cover as i rember month ago tigtning those allen key bolts there and got extremly loud then loosend them and went away but its back again.

any ideas would be great or help on this as a few people have had this problem after reserching it but all different opinions...

Edited by R33ram
Link to comment
https://www.sau.com.au/forums/topic/404972-noise-from-cam-cover/
Share on other sites
Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted (edited)

Yea mine has been making this noise ever since the timing belt was done but i had a entire kit installed bearings belt everything changed professionally now it makes this noise on a cold start and goes away once it's warmed up...

What's the worst case scenario is it something that should be fixed asap or??

Edited by Lethal_aussie
R33 Eddy Proficient

R33 Eddy

Posted
Posted

Yea mine has been making this noise ever since the timing belt was done but i had a entire kit installed bearings belt everything changed professionally now it makes this noise on a cold start and goes away once it's warmed up...

What's the worst case scenario is it something that should be fixed asap or??

yours sounds like idler, if you are worried get the belt tension checked it could be too tight, if you installed a GATES belt and had it tension to stock spec it could be over tight.. worse case the idler gives way...

R33ram Enthusiast

R33ram

Posted
  • Author
Posted

yea get it checked tommorow but hate taking it to mechanics as they are always like what noise lol

Is there any damage to be done or is it just a noise that gets annoying and no affect to engine besides that?

I did put a bit of wd40 or it got in there and became louder lol so most likley the cause is what you saying....

Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted (edited)

yours sounds like idler, if you are worried get the belt tension checked it could be too tight, if you installed a GATES belt and had it tension to stock spec it could be over tight.. worse case the idler gives way...

Yep was a gate's racing belt kit, if the idler gives away what will happen lol? Just not crank over or will it actually damage the engine on failure? If its just a noise i wont worry about it ... Was all done professionally so its all under warranty etc ill just blast the mechanic and they can cop the bill.

Edited by Lethal_aussie
Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted

Yep was a gate's racing belt kit, if the idler gives away what will happen lol? Just not crank over or will it actually damage the engine on failure? If its just a noise i wont worry about it ... Was all done professionally so its all under warranty etc ill just blast the mechanic and they can cop the bill.

Besides the noise it does on idle on a cold start ... would it get much worse before that would happen or would it just suddenly happen? I had the entire gates kit done doesn't that include new idler's etc?? paid 400 bucks be damned if it was just the belt they replaced... regardless mechanic would be at fault anyways since they installed the kit and did the timing etc??

R33 Eddy Proficient

R33 Eddy

Posted
Posted

Besides the noise it does on idle on a cold start ... would it get much worse before that would happen or would it just suddenly happen? I had the entire gates kit done doesn't that include new idler's etc?? paid 400 bucks be damned if it was just the belt they replaced... regardless mechanic would be at fault anyways since they installed the kit and did the timing etc??

Did you supply the mechanic the parts or did they suggest the parts and source the parts? Warranty might not stand if you supplied the parts...

I installed the kit myself did the tension up and it was sweet, no noise or anything for a good year, recently i had to take the belt of and when i started the car it made that exact noise but much louder, i loosened the tensioner off and the noise has gone, im not worried that the belt will slip or jump and it was a Cu*t to even get off and back on again.

Next time i will just buy genuine Nissan belt as their is nothing is wrong with them..

Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted (edited)

Did you supply the mechanic the parts or did they suggest the parts and source the parts? Warranty might not stand if you supplied the parts...

I installed the kit myself did the tension up and it was sweet, no noise or anything for a good year, recently i had to take the belt of and when i started the car it made that exact noise but much louder, i loosened the tensioner off and the noise has gone, im not worried that the belt will slip or jump and it was a Cu*t to even get off and back on again.

Next time i will just buy genuine Nissan belt as their is nothing is wrong with them..

Yea im thinking that to should of got nissan ... im thinking its kinda overkill for street use gates... yea they sourced and recommended the gates timing belt kit they go through justjap i think.. as it was stronger etc

I always pay for a professional to install and source everything as im mechanically stupid in most area's lol... short of a oil change etc

Edited by Lethal_aussie
  • 4 weeks later...
Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted

yours sounds like idler, if you are worried get the belt tension checked it could be too tight, if you installed a GATES belt and had it tension to stock spec it could be over tight.. worse case the idler gives way...

*Just a update* on this guys, Had it checked again and the noise was the Timing belt which was actually loose.. and needed to be re-tensioned so all good now, cheer's :)

Lethal_aussie Apprentice

Lethal_aussie

Posted
Posted

Hmmm

That is odd, how can the belt be loose?

I have exactly the same noise as you had, belt done months ago ..

Apparently the original mechanic that worked on my car was meant to re-tension the belt when i had the gates kit installed to begin with and didn't... The main mechanic "owner" said he had to redo the kit and tighten it as it was loose which is what was making the noise..

This is what i was told..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      Chris' Toyota Mark ii JZX110

      By GTSBoy · Posted

      I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
    • GTSBoy
      Strange issue RB25DET wont start

      By GTSBoy · Posted

      Yeah, I would have said the same. It makes me suggest that there are other things wrong, such that the ECU is totally unhappy with the broken sensor. The only other thought here is that maybe it is shorted, which might cause a different issue to the typical "disconnected" sensor.
    • Kinkstaah
      Chris' Toyota Mark ii JZX110

      By Kinkstaah · Posted

      The fact that US/JDM plates actually fit the skyline bumpers properly is a big, big thing for me as they are the correct dimensions. Annoyingly you can't opt for a normal plate (or plate combination) in that size. You have to make up your own one, and at that point you'd still know it wasn't randomly assigned. 
    • GTSBoy
      First time Skyline owner

      By GTSBoy · Posted

      Well, really, that's any ECU, because it's not so much the ECU that the tuner connects to, but a laptop that's connected to the ECU. You have to have the tuning software installed locally. The "remote" part is essentially just remote desktop (RDP) or VNC type access. Nevertheless, if you're looking to upgrade, then you're immediately in the Haltech/Link territory, both of which can be done by any number of competent tuners here in Oz. But without a dyno, you'll definitely also need a wideband O2 sensor fitted, and you'll probably be relying on "auto" tuning a bit, where you drive it around under various loads and then apply the corrections that the ECU learns (basically applying the fuel trims that the ECU has to do to correct the mixtures). Tuning the timing is a little harder. It can be difficult to trust the old OEM knock sensors on RBs, so it is definitely best to have someone who knows what they're listening for, with knock ears (a piezo microphone connected to the engine, and and little amp and headphones so the listener can hear the angry men with hammers who live in the engine). That is more difficult to do remotely, and I suspect the only sane way is to be quite conservative on timing. But that's OK. You're probably waaaaay better off with conservative timing where you are. What is the fuel situation? 98RON available? Or low grade jungle juice?
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I see your point, I didn't think too deep into it, was purely focused on the price. There's no bad blood between myself and GSM, they acknowledged the price was cheaper else where and at the time couldn't match it. 
×
×
  • Create New...