Jump to content
SAU Community

Cross Threaded Spark Plug Hole

Plattsy

By Plattsy,
in General Maintenance

 Share

Recommended Posts

Plattsy Grand Master

Plattsy

Posted
Posted

Whats the best fix gents, geezer I know has a cross threaded spark plug which may be causing a miss fire, it's on the 6th cylinder so it's a pain int the arse to get too, but can this be tapped or re plugged?

Link to comment
https://www.sau.com.au/forums/topic/405141-cross-threaded-spark-plug-hole/
Share on other sites
Plattsy Grand Master

Plattsy

Posted
  • Author
Posted

Just do what you did in europe then

tools are in Europe hence why he need's somewhere who can do it.............. and a generator is a little different to a skyline engine. if you feck the gen up nobody cares, i break his skyline he will cry!

anyone ever had it done by a mech?

to be honest even if i could borrow the tools i wouldn't feel confident.... we used to fill the hole with a rag forced into the top of the cylinder with the piston at tdc, once it was tapped we would vacuum out, remove the rag, vacuum again, then use a tiny fiber optic camera with a light to look for the fillings. it used to work. anyone confident enough to do this around the peninsula?

scotty nm35 Grand Master

scotty nm35

Posted
Posted

If you grease up the tap it should hold most of the chips in the flute, I'm guessing the thread only needs a cleanup anyway, as if the plug were fully cross threaded it would need to be removed and helicoiled.

A vacuum cleaner with a length of hose attached sounds like the go for cleaning out the bore, and those snake cameras are only $100 these days.

I doubt that is the cause of the missfire though...

533 RYC Proficient

533 RYC

Posted
Posted

Ok, heres the best & EASIEST way to do it WITHOUT getting anything in the cylinder. I work in heavy engineering, & am an engineer. Showed an apprentice this trick yesterday after he f**ked an oil gallery plug hole on an installed crankshaft. (7,042 c.i. V12). Compressed air is required.

1. Bar engine over till intake valves for cylinder are open, exhaust valves closed.

2. Find a suitable vaccuum port on inlet manifold, try to clamp other hoses/passages temporaily.

3. Rig up an air line attachment to the port with an inline valve to regulate supplied air to the cylinder.

4. Remove spark plug.

5. Slowly open valve. You should be able to feel air blowing out of the spark plug hole.

6. Run tap DRY into hole & slowly re-tap thread. All filings will be carried out with the air, so watch your eyes!

might take alittle bit depending on how bad the thread is. Using this method has worked EVERYTIME WITHOUT FAIL!!!!!!!!!

Plattsy Grand Master

Plattsy

Posted
  • Author
Posted

it doesn't seem to bad. its at a very slight angle, towards the front of the engine, i say i think its misfiring but not actually sure car drives perfectly, but we changed the knackered coil packs, and the one on that spark plug was cracked, and it seemed like it was because of the angle it was attached.its not a major issue, but its just gonna cost a fair bit if it keeps cracking coils.

cheers for all the input fellas, we just really dont have the tools or equipment to do it ourselves. rather pay out 100 bucks or so rather than having to forkout for a new head/gasket/ancillarys etc.

Plattsy Grand Master

Plattsy

Posted
  • Author
Posted

Ok, heres the best & EASIEST way to do it WITHOUT getting anything in the cylinder. I work in heavy engineering, & am an engineer. Showed an apprentice this trick yesterday after he f**ked an oil gallery plug hole on an installed crankshaft. (7,042 c.i. V12). Compressed air is required.

1. Bar engine over till intake valves for cylinder are open, exhaust valves closed.

2. Find a suitable vaccuum port on inlet manifold, try to clamp other hoses/passages temporaily.

3. Rig up an air line attachment to the port with an inline valve to regulate supplied air to the cylinder.

4. Remove spark plug.

5. Slowly open valve. You should be able to feel air blowing out of the spark plug hole.

6. Run tap DRY into hole & slowly re-tap thread. All filings will be carried out with the air, so watch your eyes!

might take alittle bit depending on how bad the thread is. Using this method has worked EVERYTIME WITHOUT FAIL!!!!!!!!!

shame your in sydney boss, otherwise we would be round with some beer for ya in exchange!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • GTSBoy
      Boost cut after swap(RB25DET NEO) R34

      By GTSBoy · Posted

      The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • Kapr
      Boost cut after swap(RB25DET NEO) R34

      By Kapr · Posted

      So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
    • JC71
      new 1.5 LSD issues/concerns

      By JC71 · Posted

      the Tomei LSD fluid with lsd kit. frustrated that it was shaking the car to crap and affecting everything else negatively, I pulled the diff last night, and removed the lsd carrier, could not find anything wrong, however it seem to be 100 locked up acceleration, and deacceleration, wondering if they sent me a 2 way not a 1.5??  either way I installed the stock open carrier back in place. test drove everything smooth as butter again. no shake, shutter, random, what felt like clutch slip and grab or drive shaft play, etc. something differently wrong in side the lsd. I might bother taking it apart (if possible) to figure out what's going on inside this carrier, as bought too long ago to return.  only draw back is its back to a one wheel wonder.
    • TurboTapin
      Most women will agree that parking is the most taxing part of driving

      By TurboTapin · Posted

      What a time to be alive!!
×
×
  • Create New...