Jump to content
SAU Community

Recommended Posts

Whats the best fix gents, geezer I know has a cross threaded spark plug which may be causing a miss fire, it's on the 6th cylinder so it's a pain int the arse to get too, but can this be tapped or re plugged?

Link to comment
https://www.sau.com.au/forums/topic/405141-cross-threaded-spark-plug-hole/
Share on other sites

Just do what you did in europe then

tools are in Europe hence why he need's somewhere who can do it.............. and a generator is a little different to a skyline engine. if you feck the gen up nobody cares, i break his skyline he will cry!

anyone ever had it done by a mech?

to be honest even if i could borrow the tools i wouldn't feel confident.... we used to fill the hole with a rag forced into the top of the cylinder with the piston at tdc, once it was tapped we would vacuum out, remove the rag, vacuum again, then use a tiny fiber optic camera with a light to look for the fillings. it used to work. anyone confident enough to do this around the peninsula?

If you grease up the tap it should hold most of the chips in the flute, I'm guessing the thread only needs a cleanup anyway, as if the plug were fully cross threaded it would need to be removed and helicoiled.

A vacuum cleaner with a length of hose attached sounds like the go for cleaning out the bore, and those snake cameras are only $100 these days.

I doubt that is the cause of the missfire though...

Ok, heres the best & EASIEST way to do it WITHOUT getting anything in the cylinder. I work in heavy engineering, & am an engineer. Showed an apprentice this trick yesterday after he f**ked an oil gallery plug hole on an installed crankshaft. (7,042 c.i. V12). Compressed air is required.

1. Bar engine over till intake valves for cylinder are open, exhaust valves closed.

2. Find a suitable vaccuum port on inlet manifold, try to clamp other hoses/passages temporaily.

3. Rig up an air line attachment to the port with an inline valve to regulate supplied air to the cylinder.

4. Remove spark plug.

5. Slowly open valve. You should be able to feel air blowing out of the spark plug hole.

6. Run tap DRY into hole & slowly re-tap thread. All filings will be carried out with the air, so watch your eyes!

might take alittle bit depending on how bad the thread is. Using this method has worked EVERYTIME WITHOUT FAIL!!!!!!!!!

it doesn't seem to bad. its at a very slight angle, towards the front of the engine, i say i think its misfiring but not actually sure car drives perfectly, but we changed the knackered coil packs, and the one on that spark plug was cracked, and it seemed like it was because of the angle it was attached.its not a major issue, but its just gonna cost a fair bit if it keeps cracking coils.

cheers for all the input fellas, we just really dont have the tools or equipment to do it ourselves. rather pay out 100 bucks or so rather than having to forkout for a new head/gasket/ancillarys etc.

Ok, heres the best & EASIEST way to do it WITHOUT getting anything in the cylinder. I work in heavy engineering, & am an engineer. Showed an apprentice this trick yesterday after he f**ked an oil gallery plug hole on an installed crankshaft. (7,042 c.i. V12). Compressed air is required.

1. Bar engine over till intake valves for cylinder are open, exhaust valves closed.

2. Find a suitable vaccuum port on inlet manifold, try to clamp other hoses/passages temporaily.

3. Rig up an air line attachment to the port with an inline valve to regulate supplied air to the cylinder.

4. Remove spark plug.

5. Slowly open valve. You should be able to feel air blowing out of the spark plug hole.

6. Run tap DRY into hole & slowly re-tap thread. All filings will be carried out with the air, so watch your eyes!

might take alittle bit depending on how bad the thread is. Using this method has worked EVERYTIME WITHOUT FAIL!!!!!!!!!

shame your in sydney boss, otherwise we would be round with some beer for ya in exchange!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It might be worth having a good look at the chassis behind the bumper then; most people prefer the series 2 look so it might have been changed to cheaper parts as part of an earlier repair
    • The car itself a series 2. I was just curious about the headlights and just wanted to confirm that they were series 1. Good to know the rest of the front end is series 1. It’ll be easier for me to find parts on the aftermarket side of things lol
    • If you've wired up the coils & injectors properly, & have the neo CAS loom for the trigger, it should all work. The VCT works the same way so just different plugs between s1 & neo. Assuming DBW if no IAC. Don't bother with the stock boost solenoid with g4x.
    • THERE IS NO IAT SENSOR ON ANY SINGLE TURBO RB. And the one on an RB26 is not for "engine control" - it's really too big and too slow and is only used for over-temp alarming (as far as I can tell). Anyway, you don't have one. You want/need one for the Link, then you need to buy one, find a spot for it, and wire it in. You do know that the stock boost solenoid is not capable of "control", right? It is merely on or off, for the low boost (5 psi) and high boost (7psi), which the ECU enforces mostly based on gear. The stock solenoid is not for PWM control and is not plumbed up in a way to provide it. If you want to control boost properly, then you need a proper MAC valve. And yes, you can wire either of them direct to the ECU. Well, I assume you can - I don't know what the boost solenoid pins on the plug and play Link are capable of. They really should be as capable as any normal Link - but seeing as it is plg and play, it might be limited to stock functionality. Read the doco.   You really do just want to plug stuff together without understanding how it works, right? I can't help you there. I don't know the plug types or pinning on half the stuff you're asking about. If I had to do it I would sit down with the wiring diagrams, the car/looms and a multimeter and work out what is what.
    • Light should be a pressure switch, not a sensor.
×
×
  • Create New...