Jump to content
SAU Community

Recommended Posts

Hey guys im new here :no:

just a quick question. my r33 gtst is blowing a lot of white smoke. it would literately fill my whole street full of smoke.

I have taken it to ultratune and they have done a compression and leak test and it came back ok. they are learning more towards a turbo issue. but they are still unsure.

is this a common thing for skylines?

if it is indeed a turbo issue they are going to upgrade to a high flow garret turbo, which leads me to my next question. how much power is this thing going to output once its installed?

specs of car

Front mount intercooler

pod air fillter

full hks exhaust

boost controller

and the garret high flow turbo.

thanks guys.

lol

seems like youve done ur bpu , so OBVIOUSLY depending on how many pounds you are running , id say anywhere from 200 - 230rwkw. youd also need to get a tune though to get this kind of power safely

Yes white smoke is usually a turbo issue if its a large amount of white smoke and the compression test came out ok.

Edited by tripsteady
  • 3 weeks later...

Hey guys...remember me? :P

wasnt the turbo...it was infact...a god damn cracked piston. 7grand later.....sigh

on the plus side. since I had the engine out...I went all out.

port and polish

overbored

ngk spark plugs

high end metal gasket

high flow garret turbocharger

new ecu

wiseco forged pistons

running 18psi boost

my mechanic thinks it will pump over 350kw at the wheels. getting it dyno tuned tomorrow with vid :)

will update tomorrow tomorrow.

so any more info on the turbo? might be a good idea to do some research on here before you spend that much coin.

every turbo will have a different result and will make the car perform very differently

so any more info on the turbo? might be a good idea to do some research on here before you spend that much coin.

every turbo will have a different result and will make the car perform very differently

Hey buddy

Its my standard turbo high flowed with garret internals. cost me $1500

still need it tuned on the dyno. not sure if I need a new ecu? cant really afford anything after spending 8grand :(

I just hope my mechanic wasnt taking me for a ride. just seems so exsessive...I mean, 8 grand? :(

drove the car all weekend to run in the new pistons. didn't boost hard, but I can already feel the car is alot more punchier and responsive.

will update soon. any advice is appreciated guys :)

My mechanic said he is going to try his best to tune it with the stock ecu. he said the car is still going to be pretty quick as it is. he is a professional drag racer so Id like to think I can trust him. he seems like an awesome guy though.

will save up for ecu later down the track

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...