Jump to content
SAU Community

Recommended Posts

Hi all,

I'm considering having a go at removing the intake plenum to replace the leaky intake gasket.

I've searched and have a comprehensive tutorial from another web forum, plus the R32 workshop manual.

Any tips or suggestions before I get stuck into the car?

Is the task as bad as some have suggested?

My major concern is replacing the many hoses - which looks like you are unable to actually see where they go!

Cheers

Link to comment
https://www.sau.com.au/forums/topic/406015-gtr-plenum-removal-advice/
Share on other sites

Have done a few of these in the car. Best way is to remove the clutch and brake boosters. You can leave the master cylinders still attached to the lines, just unclip them at the firewall and move them out the way. There will be 3 bolts holding your IAC valve to the manifold, they need to be removed, diff breather tube needs to be removed where it bolts to manifold, also the bracket for the oil pressure sensor and maybe your clutch/brake booster Vac hardlines. From memory with all those unbolted its all easy street.

Id recommend a good 1/4 socket set with a good uni joint and some decent rachet ring spanners(flex head will be good too). Make sure you have a good feel of all the hoses while its all off (if i was you id be getting all new GENUINE hoses to save yourself the trouble later down the track).

With the throttle bodys make sure after you have cleaned them to check the throttle plates are still sealing in its housing ok. Most times when you clean the throttle bodys out you will need to re-seal them as there is a wax which forms a "perfect seal" between the plate and its housing. Can you use the Tomei throttle coat which work a treat.

Hope that helps!

Same as others have said, have a good quarter drive socket set ready with a good uni joint and heaps of extensions. I found the idle control valve assembly would only come off from long extensions and laying on the ground looking up at the bottom o the intake. It feels like you'll break the extensions. They can be tight!

upgrade to nitto, hks, tomei etc, and use hylomar gasket spray on both sides.

Hylomar gasket spray is a must. Very good stuff. If you where located in Perth I would have sold you a spare Tomei inlet/throttle body metal gasket set I have.

Cheers guys - after a bit of thought, I decided to contact a different import mechanic, whom has only quoted my $400 to do the job!

Considering its a relatively small amount of money (compared to my original quote!) - well worth having someone else take on the task.

Strange tho as I'm slightly saddened that I wont get the chance to be in the shed for a few days with my head under the bonnet (I think us car fanatics are a strange breed!)

  • 4 months later...

Been a while since I started this post!

I got it fixed for the quoted 400 - did a great job, no leaks, and replaced a few hoses.

The guy even polished the intake plenum up for cheap too - looks good!

Down side is there must be a slight leak elsewhere as it still idles at about 11-1200 (better then the previous 14-1500!)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I know people cry at the price of the Getrag 12-14k for a conversion now, but it really is a nice mid point. Not going to get change from 10k on a gearset installed.  $30k++ for sequential.   I know you run the risk of a damaged used one and parts are hard to get but as a street car gearbox its really hard to beat. If you enjoy a more traditional manual, its the choice no question.     
    • Time to decide what’s more import, your power level or your budget because you’re going to struggle to keep both 
    • Our Southern Highlands Cruise is proudly registered with “R U OK?” Day.  Sometimes the best way to check in on your mates is by getting out for a drive together. Sharing a common passion like cars creates the perfect space to chat, connect, and support each other.  A simple “R U OK?” can make all the difference. Let's enjoy the drive, the company, and look out for one another. PLEASE WEAR YELLOW FOR “R U OK?” DAY Sunday 14th September 2025 9:30AM Meeting Crossroads Homemaker Centre 10:00AM Cruise Departure Via Old Hume Hwy 11:45AM Arrival at Mittagong RSL Club Meet Location: Crossroads Homemaker Centre Final Destination: Mittagong RSL Club *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yep, its been down for a while, as I understand it it will be back soon.
    • Yeah I also looked at Plazmaman, but, it ended up alot  cheaper getting black ones through EFI when you also added in the delivery cost
×
×
  • Create New...