Jump to content
SAU Community

Recommended Posts

Hi all,

I'm considering having a go at removing the intake plenum to replace the leaky intake gasket.

I've searched and have a comprehensive tutorial from another web forum, plus the R32 workshop manual.

Any tips or suggestions before I get stuck into the car?

Is the task as bad as some have suggested?

My major concern is replacing the many hoses - which looks like you are unable to actually see where they go!

Cheers

Link to comment
https://www.sau.com.au/forums/topic/406015-gtr-plenum-removal-advice/
Share on other sites

Have done a few of these in the car. Best way is to remove the clutch and brake boosters. You can leave the master cylinders still attached to the lines, just unclip them at the firewall and move them out the way. There will be 3 bolts holding your IAC valve to the manifold, they need to be removed, diff breather tube needs to be removed where it bolts to manifold, also the bracket for the oil pressure sensor and maybe your clutch/brake booster Vac hardlines. From memory with all those unbolted its all easy street.

Id recommend a good 1/4 socket set with a good uni joint and some decent rachet ring spanners(flex head will be good too). Make sure you have a good feel of all the hoses while its all off (if i was you id be getting all new GENUINE hoses to save yourself the trouble later down the track).

With the throttle bodys make sure after you have cleaned them to check the throttle plates are still sealing in its housing ok. Most times when you clean the throttle bodys out you will need to re-seal them as there is a wax which forms a "perfect seal" between the plate and its housing. Can you use the Tomei throttle coat which work a treat.

Hope that helps!

Same as others have said, have a good quarter drive socket set ready with a good uni joint and heaps of extensions. I found the idle control valve assembly would only come off from long extensions and laying on the ground looking up at the bottom o the intake. It feels like you'll break the extensions. They can be tight!

upgrade to nitto, hks, tomei etc, and use hylomar gasket spray on both sides.

Hylomar gasket spray is a must. Very good stuff. If you where located in Perth I would have sold you a spare Tomei inlet/throttle body metal gasket set I have.

Cheers guys - after a bit of thought, I decided to contact a different import mechanic, whom has only quoted my $400 to do the job!

Considering its a relatively small amount of money (compared to my original quote!) - well worth having someone else take on the task.

Strange tho as I'm slightly saddened that I wont get the chance to be in the shed for a few days with my head under the bonnet (I think us car fanatics are a strange breed!)

  • 4 months later...

Been a while since I started this post!

I got it fixed for the quoted 400 - did a great job, no leaks, and replaced a few hoses.

The guy even polished the intake plenum up for cheap too - looks good!

Down side is there must be a slight leak elsewhere as it still idles at about 11-1200 (better then the previous 14-1500!)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...