Jump to content
SAU Community

Recommended Posts

Just found out that the law doesn't require me to have a cat. so I've decided to get some pipe and make a few flanges. Anything to look out for when i'm doing this? i know there's currently a temp sensor but i just want to cable tie it out of the way for now.

Also, will this give the car a better sound? as it already has a nismo 3" exhaust. is the cat holding me back from a better note?

Cheers

http://www.youtube.com/watch?v=bsIrz_LaHdo

Link to comment
https://www.sau.com.au/forums/topic/406140-de-cat-advice/
Share on other sites

Pretty sure the law says you need a cat !! If the car came from oem that way , your not going to feel a lot of power over a hiflow car , only noise that makes it sound faster

A decrease if your cat expands pipe goes from 2.5 ,3 to 5in the air turbulence actually makes less power

Plus smells like hell to idle

The fine is huge if your not running a cat or shop removes it for street use

After running no cat on NA rx7 for 11 yrs except for 15 min california style emissions test only to remove it again , on that full race motor i noticed it a lot but the factory intakes etc had to be put back on to pass too and a bottle of emmisions pass junk poured into the tank for the test on bridgeport motor

Its not worth it buy a 100cell for 200 bucks which is sorta legal anyway

Can be drone at speed which is super annoying

My 2 c

Link to comment
https://www.sau.com.au/forums/topic/406140-de-cat-advice/#findComment-6471385
Share on other sites

I gutted my 3" cat and felt and heard no difference. Kakimoto 3" exhaust.

But there was the occasional bang of a back fire changing gears or just backing off the accelerator.

And yeah I'm pretty sure by law you need to run a cat. I think if the car is pre '85 (or somewhere around there) then no hotdog or cat required, just mufflers.

Link to comment
https://www.sau.com.au/forums/topic/406140-de-cat-advice/#findComment-6471431
Share on other sites

Carbon 34,

OP is from NZ - cats are not a requirement there, I'm lead to believe.

I thought the same thing, but I believe this has been revised.

http://www.transport.govt.nz/legislation/Vehicle-Emissions-Questions-and-Answers/

Link to comment
https://www.sau.com.au/forums/topic/406140-de-cat-advice/#findComment-6472514
Share on other sites

Cheers for the input, the car is registered as a special interest vehicle (used to exempt cars from NZ regulations on frontal impact and emissions) which the R32 GTR classes as.

The car sounds quite droney already and it does occasionally spit when on the overrun and changing gears, see what the story is on the weekend.

Link to comment
https://www.sau.com.au/forums/topic/406140-de-cat-advice/#findComment-6472518
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...