Jump to content
SAU Community

Need To Identify And Replace This Coolant Pipe

damono

By damono,
in General Maintenance

 Share

Recommended Posts

damono Proficient

damono

Posted
Posted

Hi,

My mechanic has identifie my water leak to a corroded metal pipe with a couple of connections for coolant/heater, its located under the intake and I think it runs parallel somewhere between near where the thermostat is located and towards the firewall, but cant be sure as I didnt pull it apart. He's sent me a pic (attached), and I need to find a replacement or at least the name of the pipe so I can track one down. Cars off the road until I find one.

Anyone can identify and point me in the right direction on getting a replacement would be awesome :)

cheers

XYSMK.jpg

damono Proficient

damono

Posted
  • Author
Posted

Cool, possibly could be. Like I said, haven't seen it myself where it came from, only this pic :)

He said one end comes from a fitting on the block to a short rubber hose to this cross section. It's a joint with each end being 3/4inch, one side has 5/16in and other 1/2in connector. Hopefully means more to you than me haha

damono Proficient

damono

Posted
  • Author
Posted

Found an exploded diagram and looks like it might be the Pipe assembly heater feed, p/n 14075n on this diagram

http://www.skylinesaustralia.com/forums/index.php?app=core&module=attach&section=attach&attach_rel_module=post&attach_id=249116

  • 3 years later...
wagon Collaborator

wagon

Posted
Posted (edited)

I'm in need of the same part as well as a few others. Only thing is that mine is a Stagea and the diagram doesn't seem to have that part.

Mechanic said he was also after the 2 Circled parts plus

1* metal pipe connector

2* plastic fittings

1* Inlet Gasket

1* Plenum Gasket.

Can anyone please help...

post-18088-0-23835900-1460963906_thumb.jpg

Edited by wagon
discopotato03 Grand Master

discopotato03

Posted
Posted (edited)

For an ECR33 the part number is 1405321U00 and on my invoice its called PIPE, WATER-OIL COOLER .

They are only available ex Japan and mine came via John Robinson Nissan Rockdale in Sydney .

I ordered everything under the manifold hose and tube wise that see's coolant including the screw in rear block fitting and the press in water pump end one and the longer tube that hangs under the manifold .

Search ECR33 followed any of those part numbers on the Nissan diagrams . Brings up an American site with the schematic and actual part numbers .

A .

Edited by discopotato03
wagon Collaborator

wagon

Posted
Posted

I think i have confused myself. Not non turbo but series one. The part looks as if it is that part in the op's pic above but that doesn't seem to be on a series one (96 model)

#http://nissan.epcdata.ru/stagea/wgnc34/5411-rb25det/engine/211/#211C_002

Seems an awful lot more parts on the later models?

  • 1 year later...
iruvyouskyrine Grand Master

iruvyouskyrine

Posted
Posted
8 hours ago, Mooglymoog said:

Bump. I need this weird fitting for an RB 20 DET red top. Does anyone know where to get one? Part number? I found a diagram and I think it is 14020HA or something. 

post a pic of what you need, i probably have one

bakwoods Contributor

bakwoods

Posted
Posted

I actually just took off my lower runners and have the same exact issue with mine as the first post. Quite honestly I was thinking of just cutting the rotted metal part out and securing the new hose to whatever is left.

Although I've had no luck with diagrams as of late so if anyone has part numbers I'm sure there's some interchangeable parts between the 240SX/300ZX heater hose wise. It'd be nice not to fork over $300+ for a hose kit.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • bilbo117
      R34 GTR Seats / No longer reclining

      By bilbo117 · Posted

      Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • Dose Pipe Sutututu
      Ethanol Content Sensor - Always at 11%?

      By Dose Pipe Sutututu · Posted

      Those above shitboxes, mediocre and above usually have a turbo strapped to them, hence the slightly higher octane is required.  
    • sinn3r
      R34 Skyline climate control unit transistor

      By sinn3r · Posted

      Hi all,   long time listener, first time caller   i was wondering if anyone can help me identify a transistor on the climate control unit board that decided to fry itself   I've circled it in the attached photo   any help would be appreciated
    • Kinkstaah
      Blue slip

      By Kinkstaah · Posted

      I mean, I got two VASS engineers to refuse to cert my own coilovers stating those very laws. Appendix B makes it pretty clear what it considers 'Variable Suspension' to be. In my lived experience they can't certify something that isn't actually in the list as something that requires certification. In the VASS engineering checklist they have to complete (LS3/NCOP11) and sign on there is nothing there. All the references inside NCOP11 state that if it's variable by the driver that height needs to maintain 100mm while the car is in motion. It states the car is lowered lowering blocks and other types of things are acceptable. Dialling out a shock is about as 'user adjustable' as changing any other suspension component lol. I wanted to have it signed off to dissuade HWP and RWC testers to state the suspension is legal to avoid having this discussion with them. The real problem is that Police and RWC/Pink/Blue slip people will say it needs engineering, and the engineers will state it doesn't need engineering. It is hugely irritating when aforementioned people get all "i know the rules mate feck off" when they don't, and the actual engineers are pleasant as all hell and do know the rules. Cars failing RWC for things that aren't listed in the RWC requirements is another thing here entirely!
    • GTSBoy
      Best place to order Authetic R32 Parts in Japan

      By GTSBoy · Posted

      I don't. I mean, mine's not a GTR, but it is a 32 with a lot of GTR stuff on it. But regardless, I typically buy from local suppliers. Getting stuff from Japan is seldom worth the pain. Buying from RHDJapan usually ends up in the final total of your basket being about double what you thought it would be, after all the bullshit fees and such are added on.
×
×
  • Create New...