Jump to content
SAU Community

Recommended Posts

Hi, looking in my dash as im going to swap my xanavi unit for the standard air con unit. I found some aftermarket wiring and traced it back to this. Anyone know what the white box is and what has been wired into it.

-White box found under far left of dash, just to the left when the glove box is removed.

-Black box found behind the xanavi headunit, with a few metres of blue & yellow cable taped up. (Not connected to anything).

Just curious as to what this could be as it looks aftermarket and wonder what it does. or what it is meant to be able to do

post-96096-0-36485400-1344229518_thumb.jpg

post-96096-0-24030100-1344229523_thumb.jpg

post-96096-0-88473000-1344229527_thumb.jpg

Thanks

Edited by Nadnerb

Any numbers or writing on them? The black box looks a bit like a speed cut defeat for getting rid of the 180km/hr peed limit but tbh could be anything.

Maybe the white box is what is needed for the interior light delay! What are the numbers on it?

Have a closer look at it and see if theres a brand or anything on it, I've found cables to nowhere under my passenger seat, behind my dash and also the cables and transformer for reverse sensors I don't have so there's a good chance whatever it was for has been stripped from your car, oh yeah I also have two on off switches that don't do anything haha

Also not to thread hijack but semi related, my air con unit doesn't function completely, ie if it's on 18 degrees I get coldest air, if i move it one notch to 19 I get air hotter then the fires of hell, and I also have no lights on the bottom row of buttons, could this indicate I had xanavi once and someone has done a half arse job of switching it?

Edited by Chris_Beli

White box on far left of dash is connected to your central locking, I believe its the reciever for your key.

When I installed my immobiliser we had the dash apart under the steering column trying to find a signal from a box on the passenger side.

Annoying.

Hi thanks, yer white box number is 28595 0v005 . I google searched it and found alot of japanese writing, but used google translator and found that;

The White box pictured is the Nissan Stagea keyless computer (translated)

The little black box that has been wired in only has Japanese writing on it, so not sure what it is or does yet, but it looks to be aftermarket add-on.

The black box looks like it has a button on the front from the last picture. Does it look like a card reader?

In the first picture there is something else in the back of the foot well is that connected to any of it and what is it.

The black box looks like it has a button on the front from the last picture. Does it look like a card reader?

In the first picture there is something else in the back of the foot well is that connected to any of it and what is it.

Hey, The thing that looks like a protruding button is just a clip that holds it together im pretty sure. theres no card reader on it either

The thing in the footwell corner is my crossover for the speakers.

Also not to thread hijack but semi related, my air con unit doesn't function completely, ie if it's on 18 degrees I get coldest air, if i move it one notch to 19 I get air hotter then the fires of hell, and I also have no lights on the bottom row of buttons, could this indicate I had xanavi once and someone has done a half arse job of switching it?

I dare say your HVAC controller is playing up. Have you checked the resistance in the globes for your buttons? Mine were fried, replaced them 6 months ago ( genuine P/N: 27545-0N002 for the short ones for the button illumination, & 27545 - 8E100 for the three long ones for the LCD illumination).

Have you tried unplugging them to see what dosen't work. Does the black box wire upto the white box it looks like it has the same colour wires out of each box. And the blue and yellow like like a switch wire. See if there is volts on 1 of them or try touching them together.

Also

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...