Jump to content
SAU Community

Recommended Posts

Guys,

Have noticed when I do long trips in stagea every now and then my boost will.go from 9/10 pound to getting restricted to 5pound till I reset ecu via turning off car. No dash warning lights and yes they work. Any ideas guys??

Edited by joshm35
Link to comment
https://www.sau.com.au/forums/topic/406537-m35-boost-issue/
Share on other sites

I had a problem with the Boost Solonoid where instead of getting 13psi max boost I would get only 7psi.

My problem had no CEL light and was solved each time by turning the car off and restarting. The cause always seemed to be giving it a few revs up a particular hill.

I changed my Boost solonoid and the problem was solved. The Boost solonoid sits on the passenger side of the car under the plastic engine cover. It is bolted to the side of the plenum and has 2 small rubber hoses running out one side, 1 to the intake and 1 to the turbo actuator and one hose rinning to the front of the car that connects via a T piece to the boost sensor on the intake.

I believe you can clean a solenoid but I did not try that.

Cheers

Andy

Link to comment
https://www.sau.com.au/forums/topic/406537-m35-boost-issue/#findComment-6478256
Share on other sites

If the solenoid is blocked it will lower the boost, if there is a leak it may go higher causing the ecu to pull it back.

The hose from the solenoid that T's into the boost line has a restrictor in it. If it has been replaced that could make the boost rise too high causing the same issue. Have you changed the exhaust to 3 inch? that would cause it to run higher too.

A way around it is to trick the stock map sensor into thinking the pressure is fine, you could use a small pressure regulator if you wanted, set to 12psi, but I would be getting a better boost gauge first.

Link to comment
https://www.sau.com.au/forums/topic/406537-m35-boost-issue/#findComment-6478291
Share on other sites

i removed the factory one and replaced it with a turbosmart easy 5 mins fix. Boost comes on much better and smoother now.

QFT.

Buy boost gauge

replace with a turbosmart(or the sort) set it to 14psi or whatever the boost setting is and bypass the lines for the standard solenoid. Leave the standard one plugged in to avoid CEL. problem solved.

Edited by Sunkist
Link to comment
https://www.sau.com.au/forums/topic/406537-m35-boost-issue/#findComment-6478382
Share on other sites

I had a problem with the Boost Solonoid where instead of getting 13psi max boost I would get only 7psi.

My problem had no CEL light and was solved each time by turning the car off and restarting. The cause always seemed to be giving it a few revs up a particular hill.

I changed my Boost solonoid and the problem was solved. The Boost solonoid sits on the passenger side of the car under the plastic engine cover. It is bolted to the side of the plenum and has 2 small rubber hoses running out one side, 1 to the intake and 1 to the turbo actuator and one hose rinning to the front of the car that connects via a T piece to the boost sensor on the intake.

I believe you can clean a solenoid but I did not try that.

Cheers

Andy

This sounds exactly whats going on. Do you know the price and numbers of a new solinoid?

Link to comment
https://www.sau.com.au/forums/topic/406537-m35-boost-issue/#findComment-6478525
Share on other sites

If the solenoid is blocked it will lower the boost, if there is a leak it may go higher causing the ecu to pull it back.

The hose from the solenoid that T's into the boost line has a restrictor in it. If it has been replaced that could make the boost rise too high causing the same issue. Have you changed the exhaust to 3 inch? that would cause it to run higher too.

A way around it is to trick the stock map sensor into thinking the pressure is fine, you could use a small pressure regulator if you wanted, set to 12psi, but I would be getting a better boost gauge first.

Standard hoses and exhaust

Link to comment
https://www.sau.com.au/forums/topic/406537-m35-boost-issue/#findComment-6478527
Share on other sites

for now? its what I would be doing permanently.. keeping or replacing the solenoid is not going to fix the factory safety drop in boost. it is spiking with the cold weather and/or not allowing the car to warm up before boosting. mine used to do it all the time and it pissed me off. the only way to get around it is by bypassing the solenoid with a manual/electronic boost controller.

once again: problem solved.

plus i cant imagine the worth it:price ratio for a new solenoid, which is most likely not going to fix the issue.

Link to comment
https://www.sau.com.au/forums/topic/406537-m35-boost-issue/#findComment-6478798
Share on other sites

This sounds exactly whats going on. Do you know the price and numbers of a new solinoid?

No, don't know the cost. BUT either take up Scotts offer or get an aftermarker boost controller. Even with the wastgate actuator spring Mod the car felt stronger on initial boost when I used the Greddy Profec B boost controller. It bypasses the factory one so no more problem.

Cheers

Andy

Link to comment
https://www.sau.com.au/forums/topic/406537-m35-boost-issue/#findComment-6479728
Share on other sites

yeah i thought of keeping it though it's one less thing i gotta worry about second guessing me bleed valve :)

Just keep it in the glove box or boot hiding spaces, if the problem ever occurs plug it in and drive home?

Link to comment
https://www.sau.com.au/forums/topic/406537-m35-boost-issue/#findComment-6481080
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...