Jump to content
SAU Community

Recommended Posts

  • 1 year later...

The thermostat is on the bottom hose

Yep, I have no problem locating it, but getting the tools to undo the thermo housing is a pain in the ass. Should i try using a spanner from underneath the car? I just can't reach the bolt directly under the intake

Thread bump.

I have a nsimo thermostat ready to go in mine, but find it almost impossible to reach the top bolts which is directly under the intake manifold & next to the fuel lines. Any tips?

Is it a low temp one? if so I would think about whether or not to use it.

Is it a low temp one? if so I would think about whether or not to use it.

Yep low temp - 65 degrees.

The car is running an a power FC, so i would have thought the standard ECU cold start/ enrichment ratios won't be affected from lower temp thermo?

What are your opinions on this?

Yep low temp - 65 degrees.

The car is running an a power FC, so i would have thought the standard ECU cold start/ enrichment ratios won't be affected from lower temp thermo?

What are your opinions on this?

Check your temp correction tables in your PowerFC, see when the enrichment is cut out. Really depends how it is set, if it's set to cut out over 70 then you'll always be running with addition injection correction.

I still prefer factory spec thermostats, you would want your water temps about 80~90 as it will warm up your oil too (that's my opinion).

Car is not overheating. At idle stays at about 89 deg, and cruising between 89-92 depending on weather and style of driving.

My tuner mentioned that the thermostat is possibly sticking as when tuning he noticed the bottom hose didn't seem to warm up alot.

I had the opportunity to but the nismo item so i did!

Might end up selling it, but going to speak with my tuner first.

I can't recall if you can see the temperature enrichment tables using the hand controller, if so see what the settings are like

it would be something like

50 = 1.15

60 = 1.10

70 = 1.05

80 = 1

90 = 1

100 = 1.10

110 = 1.20

etc...

Column A = Temperature

Column B = Enrichment Applied

you'll have some minor temperature enrichment as it will interpolate between 50 ~ 80 degrees

So say if your thermostat always reads 65 then on partial load your correction would be about 1.03 - ((80 - 50)/100 * 0.03) = 1.009 and on high load, i.e pedal down around 1.025

which isn't all that much, but you're burning extra fuel you don't need to lol

  • Like 1

Leave the standard temp thermo in. Why run an engine cooler than what it was designed for? If its for an overheating problem, sort out your cooling, don't "band aid" the issue.

Nope, no overheating problem. Cooling system is fine. After taking all your feedback on board, i will be going with a Tridon T"stat - 71 degree item.

But, for shits and giggles because i have the Nismo T"stat lying around, I chucked it in anyway today to see how much difference it really makes.

On idle sat at roughly 70-72 degrees, and cruising and giving it a bit water temps were between 78-80

Not overly cold, but still on the colder side of temps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...